ATMEGA128的EEPROM驱动程序，对自己编写端口驱动的同志有很大的帮助！...

三菱梯形图转成51单片机HEX文件。 三菱软件写好梯形图，再运行转换软件，设定好51单片机的输入输出， 打开写好的梯形图，转换出的就是hex文件，烧录到51单片机，51单片机 就可以执行PLC的动作了。51单片机控制板价格便宜，可以代替简单场 合的PLC，控制成本降低。 1：把PWM转换后，在PWM文件下生成一个HEX文件。 2：生成的文件很大，51单片机要选用8K以上(AT89S52就是8K)储存量的。 3：把HEX文件下载到单片机就可以用了。 -Mitsubishi ladder into 51 single-chip HEX file. Mitsubishi software written ladder, and then run the conversion software, set 51 single-chip input and output, open ladder-written, conversion is a hex file, burn to 51 single-chip, 51 single-chip microcomputer can be implementation of the action of PLC. 51 Single-chip panel prices, can replace the simple occasions PLC, control and lower the cost. 1: after the PWM converter, PWM documents generated in a HEX file. 2: generate a lot of paper, 51 single-chip 8K to choose more than (AT89S52 is 8K) storage capacity. 3: The HEX file can be downloaded to a single-chip microcomputer used.

C51单片机学习的好实例，好好学习哟，-C51 single-chip learning good examples to learn yo,呵呵呵~ ~ ~ ~

keilc + proteus 并行口设计指示灯实验 要求：掌握80C51单片机输入输出接口使用方法 学会开关量输入输出控制的接口技术及编程方法 实验题目：8个发光二极管D1~D8分别接在单片机P1.0-P1.7端口上，一个开关接在P3.0上。要求输出端口输出 “0”时，发光二极管亮。开关闭合时，开始按P1.0-P1.1-...-P1.7的顺序依次点亮LED，再按 P1.7-P1.6 -...-P1.0的顺序点亮LED，重复循环。开关断开时，立刻停止点亮指示灯。-keilc+ proteus light parallel port design of experiments requirements: master the 80C51 microcontroller input and output interfaces Society of switch to use the amount of input and output control interface technology and programming methods Experimental subjects: eight light-emitting diodes D1 ~ D8, respectively connected to the MCU P1.0-P1 .7 port on a switch connected to the P3.0 on. Requested output port output " 0" , the light-emitting diode light. Is closed, to embark on the P1.0-P1.1-...- P1.7 in the order light LED, and then P1.7-P1.6-...- P1.0 order light LED Repeat cycle. Switch off when the stop light indicator.

是台湾松翰公司8位单片机编程器的英文使用说明。-Taiwan Sonix 8-bit single-chip companies programmer for use in English.

* 本程序包含控制外部液晶面板的4-BIT控制模式子 * * 程序。这些程序是专门为 MCU201 workshop演示板 * * 设计的。但它也可作为其他类型的使用 KS0066U控 * * 制器的液晶面板的控制程序。-* The procedures include external LCD control of the four-BIT- control mode** procedures. These procedures are specifically for MCU201 workshop demonstration board** design. It can also be used for other types of use** KS0066U control system for the LCD control procedures.

这是用PIC芯片处理USB的源代码,包括初始化USB，中断设置等，是汇编语言入门USB操作的很好参考程序！-This is the PIC chip USB source code, including the USB initialization, interrupt settings, assembly language entry USB good reference operating procedure!

用于51单片机的快速DES-51 MCU for rapid DES

cstn 1.5 with ST7636的C51测试程序.-cstn ST7636 1.5 with the C51 test procedures.

水果分级，根据水果的大小自动算出经过的时间，然后控制机械部分动作实现分选-fruit grading, according to the size of fruit automatically calculate the elapsed time and then control the mechanical parts action to achieve separation

MF500非接触式IC卡开发板源程序 -MF500非接触式IC卡开发板源程序