51开发板调试程序，包括LED驱动接口，串口，AD/DA,EEPROM，蜂鸣器，键盘以及16*2LCD驱动模块，并提供单字节和字符串显示接口...

汽车遥控制的源代码.用的单片机是PIC16F72. 大批量生产.-Car remote control s source code. Singlechip is used PIC16F72. High-volume production.

具有语音功能的水温控系统, 具有语音功能的水温控系统-Voice-enabled water temperature control system, voice-enabled water temperature control system

单片机RS232/RS485串行发送实验（双机通讯）。 实验步骤： （1），准备两台598K实验机，确定1号机为发送，2号机为接收； （2），当作RS232接口实验时，1号机和2号机的P3.0和P3.1交叉相连，且两机共地； （3），当作RS485接口实验时，1号机和2号机的A、B作对应连接，同时1,2号机的R/TEN接P1.0, P3.0接R0, P3.1接DI。 （4），先运行2号机，键入[27]-->[EV]使2号机处于接收状态P。，后运行1号机[26]-->[EV]使1号机处于发送状态,P。会闪烁，在1号机键盘上按动数字键，在2号机的数码管上应显示对应的数字键值。-Send Singlechip RS232/RS485 serial experiment (two-plane communications). Experimental steps: (1), prepare two sets of experiments 598K machine, determined on the 1st machine to send, on the 2nd machine to receive (2), as a RS232 interface experiment, on the 1st and the 2nd machine and P3.0 P3.1 cross-linked, and the two planes were to (3), as a RS485 interface experiment, on the 1st and the 2nd machine A, B for the corresponding connection, while 1,2 No. of R/TEN then P1 .0, P3.0 access R0, P3.1 then DI. (4), first run on the 2nd machine, type [27]

单片机8051 MTV512,用了串口缓冲区收发合一的方式,中断 -Singlechip 8051 MTV512, serial buffer used to send and receive one way, interrupted

SAMSUNG S3C6410 CPU BSP for winmobile6-SAMSUNG S3C6410 CPU BSP for winmobile6

cstn 1.5 with ST7636的C51测试程序.-cstn ST7636 1.5 with the C51 test procedures.

用C8051F020编写的RA8803控制器320240液晶程序-C8051F020 prepared with RA8803 LCD controller 320,240 procedures

AVR单片机控制LCD液晶显示器，只有源码！-AVR片LCD液 示 源 耄

单片机驱动1602，可在1602上显示字符串，简单易懂，适合初学者使用-MCU-driven 1602, 1602 can be displayed on a string, easy to understand for beginners

内容： *红外测试程序，用单片机通过发射管发射38K的调制频率码，由一体化接收并解码由发光管显示。 *正常情况下，由于反射和高灵敏度接收，LED4（P1.3)一直闪烁，可以用黑色纸片完全遮挡接收头使 *之不能接收到发射管的信号，这是LED4熄灭。说明功能性正常 -Content:* IR test program, launched with the microcontroller through the launch tube of the modulation frequency of 38K code, by the integration to receive and decode from the LED display.* Under normal circumstances, due to reflection and high-sensitivity receiver, LED4 (P1.3) has been flickering, you can completely block the black pieces of paper to make* that they are not receiving the first emission control signal is received, it is LED4 out. Note the normal functional