ARM LPC2103在LCD12864驱动，直臂的转换功能的使用，D.

这是一个pid 程序，完成PID的计算和控制过程-This is a process pid to complete the calculation and control process PID

keil软件指南，对keilc51软件的安装、操作程序进行了详细的调试。对基尔初学者很有帮助

PC机和智能型仪表通过RS485进行异步通信-PC and intelligent instrument for asynchronous communication through the RS485

在做项目（工程）的时候，我们经常要用到比较多的按键，而且IO 资源紧张， 于是我们就想方设法地在别的模块中节省IO 口，好不容易挤出一两个IO 口，却 发现仍然不够用，实在没办法了就添加一个IC 来扫键。一个IC 虽然价格不高， 但对于大批量生产而且产品利润低的厂家来说，这是一笔不菲的开支! 那，我们能不能想到比较好的扫键方法：用最少的IO 口，扫最多的键？可以吗？-Doing the project (engineering), we often use the relatively large number of keys, and the IO resource constraints, so we are trying to save in another module IO ports, finally out of one or two IO ports, only to find is still not enough there is really no other way to add an IC to sweep on the keys. Although the price of an IC is not high, but low profits, high-volume production and product manufacturers, this is spending a lot of money! That, we can not think of a better scan key method: with a minimum of IO ports, scan Most of the keys? OK?

单片机电路图.开发者可借助此51电路原理图，大大简化开发难度，提高效率。-Single-chip circuitry. Developers can take advantage of the 51 circuit schematic diagram, greatly simplified the development of the difficulty and improve efficiency.

1.将P1.0～P1.3接开关，将P1.4～P1.7接发光二极管。依据P1.0～P1.3开关状态控制P1.4~P1.7发光二极管点亮。 2.将P1.0～P1.7全部接发光二极管，开始P1.0、P1.5点亮，左循环50次后P1.1、P1.4点亮；右循环30次，循环往复。-1. P1.0- P1.3 will then switch to P1.4- P1.7 access LEDs. P1.0- P1.3 based on state control switch P1.4- P1.7 LED lights. 2. P1.0- P1.7 will take all LEDs started Schematic, P1.5 lit, the left circle after 50 P1.1 and P1.4 lit; Turn right circle 30 times repeated.

利用51单片机的延迟函数 实现流水灯 适合不知道移位函数的初学者-51 MCU delay functions used to achieve water lamp

单片机与嵌入式系统教材简介.pdf-microcontroller and embedded systems briefing materials. Pdf

一款应用在客运系统的LED导向屏程序，采用汇编语言编写，欢迎相关人员参考-Used in a passenger transport system LED screen-oriented procedures, the use of compiled languages are welcome to the relevant reference

AVR单片机入门及C语言高效设计实践（四） ATMEAG16L的I／O端口特点及使用 ATMEAG16L单片机有32个通用I／O口，分为PA、PB、PC和PD四组，每组都是8位。这些I／O口都可以通过各自的端口寄存器设置成输入和输出（即作为普通端口使用），有些I／O口还具有第二功能（我们在后面使用到这些第二功能时再介绍）。-AVR C language portal and efficient design practice (4) ATMEAG16L the I/O Ports characteristics and use of a microcontroller ATMEAG16L 32 common I/O mouth into PA, PB, PC and PD four groups, each group are eight. These I/O I can through their respective ports Register set to input and output (that is, use as a general port), Some I/O I also have the second function (in the back of the use of these second function tell).