字母钟系统的实现代码，GPS卫星时钟对时的实现。汇编源吗

MSP430F2274单片机C语言程序实例-MSP430F2274 Singlechip C language program example

单片机音乐程序的设计与实验，包含音乐程序的设计原理。-music SCM procedures and experimental design, including music program design principles.

iar编译器调试msp430单片机c程序详细教程-iar compiler debugging MCU Controller c procedures detailed guidance

完整的实现RS232与TCP/IP网络协议的转换-Realize the full RS232 and TCP/IP network protocol conversion

51的4*4键盘驱动当按键按下时返回一个值，且只在按下键时返回一次该值，之后返回0；无按键时返回0；包含消抖功能，在键盘的下降沿触发。 基于keil平台-51 4* 4 keyboard driver when the button is depressed to return a value, and press the button only once the value to return, followed by return 0 no keys to return 0 contains extinction Buffeting function, the falling edge trigger at the keyboard. Keil-based platform

/// ////差动输入，定时启动，由T2定时//////////////// /////////选择6，7通道为ADC0差动转化通道,其中第6通道为P3.6,第7通道为P.7-/////// Differential input, time to start, from time to time T2 ///////////////////////// choose 6,7 for ADC0 channel difference Dynamic conversion channel, the first of which for the 6-channel P3.6, No. 7 channel for P.7

2051单片机的18b20温度计。有效位数为2为，程序里面以预留出小数点位，配套3位数码管即可显示。-2051 microcontroller 18b20 thermometer. 2 for the effective number of bits, the program which in order to set aside a decimal place, supporting three digital control to display.

///*** *** *** * //一、程序说明： //1, 24LC02器件地址是1010000R/W. //2, 数组写入24LC02采取页写方式. //3, 数组code从24LC02读出时采取自由读方式. //4, 采用4.00M晶体。 //5，采用软件I2C。 //二、硬件连接： //1， SDA------->23 pin.(当然你可以任意选择脚位） //2, SCL------->18 Pin.(当然你可以任意选择脚位） //3， PORTB----->数码管的段输出 //4， RD4，RD5，RC6，RC7------->数码管的位输出(数码管为共阴极） -///*******************// A description of the procedures:// 1, 24LC02 device address is 1010000R/W.// 2, write an array to take 24LC02 page write mode.// 3, the array read out the code from the 24LC02 to take a free read.// 4, using 4.00M crystal.// 5, using software I2C.// Second, the hardware to connect:// 1, SDA-------> 23 pin. (Of course, you can choose to pin)// 2, SCL-------> 18 Pin. (Of course You can choose pin)// 3, PORTB-----> digital tube output segment// 4, RD4, RD5, RC6, RC7-------> digital pipe-bit output (digital tube for a total of cathode)

在c51下液晶显示块LCD20040411的编程实例。-Under the liquid crystal display in the C51 block LCD20040411 programming examples.

（一）OCMJ8X15D的触摸屏是用模块内部控制器控制的， （二）OCMJ15X20D（V3.2）的触摸屏是用ADS7843控制的，该控制器已集成在模块上，模块已留出ADS7843的控制线供客户使用（OCMJ15X20D上的J5脚），