msp430应用系统开发典型实例 第5章程序代码

尽量朝“单片”方向设计硬件系统。系统器件越多，器件之间相互干扰也越强，功耗也增大，也不可避免地降低了系统的稳定性。随着单片机片内集成的功能越来越强，真正的片上系统SoC已经可以实现，如ST公司新近推出的μPSD32××系列产品在一块芯片上集成了80C32核、大容量FLASH存储器、SRAM、A/D、I/O、两个串口、看门狗、上电复位电路等等。 -North Korea as the "single-chip" design direction of the hardware system. System devices more mutual interference between devices are more strong, power consumption is increased, it will inevitably reduce system stability. With MCU with on-chip integration of more powerful, the real system-on-chip SoC can achieve, such as ST"s new PSD32 x x in a series chip integrates exertion nuclear, large-capacity flash memory, SRAM, A/D, I/O, 2 serial port, watchdog, the power-on reset circuit and so on.

eeprom24c128读写程序，绝对可靠-eeprom24c128 read and write procedures, absolutely reliable

非常好用的串行数据转并行数据的芯片,价格也不高,非常好用,程序经过调试,可用-very good for serial data transfer data in parallel to the chip, the price is not high, very handy, procedures after debugging, available

数据采集系统作为沟通模拟域与数字域的必不可少的桥梁有着非常重要的作用。本文介绍的重点是数据采集系统。数据采集与通信控制采用了模块化的设计，数据采集与通信控制采用了单片机8051来实现，硬件部分是以单片机为核心，还包括模-数转换模块，显示模块，和串行接口部分，还有一些简单的外围电路。8路被测电压通过通用ADC0809模-数转换，实现对采集到的数据进行模拟量到数字量的转换，由单片机对数据进行处理，用LCD显示模块来显示所采集的结果，并将数据通过串行口传输到PC机上，MCU与 PC机间的电平匹配采用MAX232接口芯片，由PC机完成数据接收和显示，VB程序编写了更加人性化的人机交互界面。-Data Acquisition System Analog domain as communication with the figure of the indispensable bridge between the domain has a very important role. This article focuses on the introduction of data acquisition system. Control data acquisition and communication of the use of a modular design, data collection and communications control to the use of a 8051 single-chip implementation, the hardware part of the single-chip microcomputer as the core, but also mold- digital conversion module, display module, and serial interface part, have some simple external circuit. 8 road test voltage through the common mode ADC0809- conversion, implementation of the collected data to the digital analog conversion, the

6段数码管分别显示，时，分，秒，四个按键，K1（P0.0），K2（P0.1）， K3（P0.2），K4（P0.3），四个按键用来调时间的，按下K1，所有位都清零显示，然后按下K2，秒在闪烁，继续按K2分闪烁，不段地按K2 秒--分--时切换着闪烁，在某位闪时按下K3相应位加一，确认调整，按K4，取消调整再按K1。在K1按下以后才有调时的功能，如果K1没有按下，按别的键没有反映。这为了在加点按键功能留着用 -6 respectively of the digital control, when, minutes and seconds, four keys, K1 (P0.0). K2 (P0.1), K3 (P0.2), K4 (width), the four keys to the transfer time, press the K1, All spaces are reset, then press K2, the scintillation seconds, according to K2 pm flickered. not according to K2 of seconds-- minutes-- when switching to flicker in certain press the flash-K3 corresponding increase in a confirmed adjustment by K4, then canceled K1 adjustment. K1 in the press will only be made after the transfer of function, if K1 pressed by other key is not reflected. This points to the function keys used Retention

串口上的128X64的LCD源程序!已编译并调试通过!-serial port on the LCD source of the built! Compiling and Debugging has passed!

温度控制的程序，自动调节蒸汽开度阀和风机的运行，来达到控制温度的要求-Temperature control program, automatically adjusts the output temperature control

Philips单片机P89C51RD和西门子Profibus工业总线的接口程序,硬件是鼎实公司的实验板,使用的鼎实公司的总线桥.-Siemens Profibus and Industrial Access Bus export procedures, hardware Teijitsu board of the company, using the company"s Teijitsu Bus Bridge.

宏芯 t103程序 能解码VGA CVBS S_VIDEO的视频解码，程序的开发环境是stc89c58rd+ 在keil c下已经编译通过-T103 Terawins procedures can decode VGA CVBS S_VIDEO video decoder, the program development environment is stc89c58rd+ In keil c have been compiled through

430成都技术培训会代码，使用IAR-4.10打开。-430 technical training in Chengdu will be the code, the use of IAR-4.10 open.