Scart To Tv 的源代码,作为接口转换是个很好的参考代码

我这是一个1602的液晶程序，是51的很精典的-I This is a 1602 LCD procedure is very classical 51

我用单片机8952和电压比较器339做了一个简单的电容容量测量表，参数大 致如下： 电容测量范围为1pF-9999.99uF，最小分辨力为1pF。分为5个量程，可以自 动切换量程，也可手动切换。 另外，有简单的频率计功能，能测量0-60MHz的数字信号频率（TTL电平）； 还可以产生几个单点频率的方波信号（比如1KHz）。 采用1602LCD作为显示器；4个按键控制；使用24C01保存当前设置值，不用 每次开机重新设置。可单5V供电，也可9V交流供电 -I used the single-chip 8952 and the voltage comparator 339 to do a simple capacitance measurement table, parameters are as follows: capacitance measurement range 1pF-9999.99uF, the minimum resolution for the 1pF. Divided into five ranges, you can automatically switch range can also be manually switched. In addition, a simple frequency meter function, capable of measuring 0-60MHz frequency digital signal (TTL level) can also lead to several single-point-frequency square-wave signal (for example, 1KHz). 1602LCD used as a monitor 4 button control use 24C01 to preserve the current settings, do not reset each boot. Can be a single 5V power supply, 9V AC power supply can also be

在ST单片机上实现GPS交通警示器功能.-In the ST to achieve single-chip GPS traffic alerts functionality.

这个是用AVR编写的程序，这里是一个时钟电路，用数码管显示当前时间。对初学者比较有用。-This is prepared by AVR process, here is a clock circuit, a digital display the current time. More useful for beginners.

本文件介绍了80C196KC与8096的区别，包括指令、寄存器结构、中断等方面的变化，有助于熟悉8096开发的人士尽快转80C196KC。-This document describes the 8096 80C196KC with the distinction, including instructions, register structure, such as interruption of changes, help with the development of the 8096 switch 80C196KC.

zlg7290的应用程序，使用哪个keil开发。c语言和汇编语言。移植性好。-zlg7290 applications, the use of which keil development. c language and assembly language. Transplantation is good.

该实验是在“点到点无线通信实验”的基础上进行开发，节点A 作为发射模块，节点B 作为射频休眠实验的对象，PC 通过串口下达休眠和唤醒的指令给节点B，来实现对射频部 件的唤醒和休眠功能。串口的设置为波特率115200b/s，8 位数据位，1 位停止位，无校验位。-The experiment in the " point to point wireless communications experiment" based on the development and launch of the module as a node A, node B as a test object dormant radio frequency, PC through the serial port sleep and wake-up instructions issued to the Node B, to achieve the right wake-up radio frequency components and the hibernation feature. Serial port baud rate is set to 115200b/s, 8 bits of data bits, 1 stop bit, no parity bit.

这是用192*64液晶实现的波形液晶显示。用的液晶型号是OCMJ4*12B，这是用正弦函数显示的。-This is 192* 64 LCD LCD waveform to achieve. LCD model is used OCMJ4* 12B, which is shown by sine function.

传感器采样电路。该硬件电路在实际电路中已经实现-Sensor sampling circuit. The hardware circuits in the actual circuit has been achieved

C8051F020的头文件，主要是本单片机的硬件地址指向等。-C8051F020 the first document, is the MCU hardware addresses at the other.