一个不错的开发板原理图,慢慢看吧> > > > > > >

stm32f rfid通讯源代码.支持双向发送接收.-stm32f rfid communication source code. in support of two-way send receive.

基于STM32串口显示温度的源程序，系统读取到温度传感器DS18B20的温度值后，通过串口，发送到电脑的串口调试助手哪里显示出来~~~

DS1302ANDSP2，详细介绍DS1302及PS2的源代码-DS1302ANDSP2, details of the source code for DS1302 and the PS2

资源描述本程序通过手机短信控制LED的亮灭 使用单片机串口2与模块通信；接法如下 STC单片机   GPRS模块 晶振选用11.0592MHz 1、板子上电后运行指示灯RUNING_LED会以一秒的频率闪烁； 2、通过芯片的串口1可以监视模块的登录情况； 3、手机发送“onled”点亮LED； 4、手机发送“offled”熄灭LED； 5、使用串口2与模块通信，串口1用于将信息打印输出。

LPC23XX系列红外（IrDA）工程文件加源代码，直接可用。-LPC23XX Series Infrared (IrDA) project file plus source code, can be used directly.

%第一步，通过差分来获得静态数据。利用积分进行还原。 %在线利用AIC计算，辨识模型，计算模型的p、q和φ参数值，然后进行预测 确定模型为ARMA（p,q)，同时求自回归系数和移动平均系数

TI DM648 DMA配置源代码,可以下接下到板子上,非常不错-TI DM648 DMA configuration source code, you can take to the board on the next, very good

优龙ARM 9 FS2410开发板的硬件电路图！很有学习价值-9 FS2410 development board hardware circuit! Very worth learning

进行arm－linux嵌入式系统开发时，需要将文件烧写到flash上，在网上可以找到win下的烧写程序，但多数情况下开发环境应该是在linux下，烧写程序时切换到win下很不方便，使用该程序可以在linux下直接对flash进行烧写 该程序运行后将一个小的for arm的c程序通过串口传送到arm开发板上，使用该小程序与主机端通信，将主机传送信息烧写到flash上- Carries on when arm- linux inserts the type system development, needs the document fever to write on flash, is on-line may find under win the fever to write the procedure, but in the most situations the development environment should be under linux, the fever writes when the procedure cuts under win not to be very convenient, uses this procedure to be allowed directly to carry on the fever under linux after flash to write this procedure movement to transmit orally a small for arm c procedure through the string delivers on the arm development board, uses this script and the main engine end correspondence, writes the main engine pass-along message pam fever on flash

1. API 为FlashDSO的接口,包含 FlashDSOAPI.DLL, FlashDSOAPI.LIB,FlashDSOAPI.H 使用手册 2.TestAPI 为FlashDSO API 的测试例程．-1. For FlashDSO API interface, included FlashDSOAPI.DLL, FlashDSOAPI.LIB. FlashDSOAPI.H manual 2.TestAPI FlashDSO API for the test test routines.