该实验室c8051f340串口

采用80C51单片机为控制核心，利用超声波传感器检测道路上的障碍，控制电动小汽车的自动避障，快慢速行驶，以及自动停车，并可以自动记录时间、里程和速度，自动寻迹和寻光功能。-80C51 single-chip microcomputer used for the control of the core, the use of ultrasonic sensors detect obstacles on the road, control of electric cars automatic obstacle avoidance, fast low traffic speeds, as well as the automatic parking, and can automatically record time, mileage and speed, automatic track finding and searching optical function.

hgf ghgfhbn yjtuyju tutdfsf-hgfhgf ghgfhbn yjtuyju tutdfsf

转载 曼码调制的非接触ID卡通用读卡程序编制 C语言代码程序如下： . /*H4001只读卡读码程序*/-reproduced Man Code Modulation non-contact reader ID cartoon programming with C language code is as follows :./* Decoding CD-card reading* /

使用MSP430和CS8900开发Web服务器，可以看到单片机的动态温度。

介绍了基于LPC932 单片机为处理器的电能表的硬件结构和软件流程-Introduction LPC932 microcontroller based energy meter processor hardware structure and software flow

利用VC提供所的MSCOMM控件实现了单片机和微机之间的串行通信，经调试已经成功-VC to provide the use of MSCOMM control and realize the single-chip serial communication between microprocessor by commissioning has been successfully

本程序用于MICROCHIP 24LC64 EEPROM的读写。本程序不使用芯片级联方式， 请将A0，A1，A2 管脚接至低电平。本程序使用IOC6作为SDA，IOC7作为SCL。 程序中的地址空间最大可至64K：24LC00-16-0，24LC01-128-8，24LC02-256-8， 24LC04-512-16，24LC08-1K-16，24LC16-2K-32，24LC32-4K-32，24LC64-8K-32， 24LC128-16K-64，24LC256-32K-64，24LC512-64K-128，读写数据均为8bits。 以上器件的格式为（型号-地址空间-页大小）不同器件的页大小不同，因此页写 程序需作相应修改，其他字节写，随机读以及顺序读程序均相同-This procedure for the MICROCHIP 24LC64 EEPROM read and write. This procedure does not use chips cascade way, please A0, A1, A2 pin to low level access. This procedure used IOC6 as SDA, IOC7 as SCL. Process address space available to the largest 64K: 24LC00-16-0, 24LC01-128-8, 24LC02-256-8, 24LC04-512-16, 24LC08-1K-16, 24LC16-2K-32, 24LC32-4K- 32,24 LC64-8K-32, 24LC128-16K-64, 24LC256-32K-64, 24LC512-64K-128, read and write data are 8bits. The format for the above device (Model- address space- page size) of different devices of different sizes of pages, so page written procedures need to be amended accordingly, and other bytes to write, rand

80C51单片机中常用CAN总线的datasheet。-80C51 single-chip CAN bus used in datasheet.

步进电机步距角细分的单片机控制系统设计和研究,主要是设计方案-stepper motor step angle breakdown of the single-chip microcomputer control system design and research, the program is designed

本系统主要用于旅游景点记录游客人数，并限制旅客的流量。采用红外传感器通过检测人体红外并对通过人数进行计数，通过红外对管将检测到的数据发送至单片机，单片机处理后送至数码管显示，数码管显示的数据即为通过的人数，并通过设定值限制旅客数量。当游客超量是系统将给出相应的提示，禁止游客再进入。以更好的保护旅游景点的生态环境。-This system is mainly used for tourist attractions recording the number of visitors and limit the flow of tourists. Use of infrared sensors by detecting the human body by infrared and number of people count on the tube will be detected by infrared the data sent to the MCU, MCU after treatment sent to the digital LED display, digital LED display of the data shall be the number of through and through setting limits the number of passengers. When the visitors over-the system will give the appropriate prompts to prohibit visitors from re-entering. To better protect the tourist attractions of the ecological environment.