基于ATMEGA88 实现的漏电保护的程序源代码

频率计的设计,单片机初学者必须程序,适用于proteus-Frequency of the design, single-chip microcomputer program for beginners to be applicable to proteus

一个关于AD590温度传感器的设计源程序附录D++设计源程序-AD590 temperature sensor on the design of source code in Appendix D++ Design source

汽车领lin总线通讯程序，非常有参考价值，请大家用的时候最好有lin总线的知识-Automotive collar lin bus communication procedures, a very valuable reference, please use the time everyone has the best knowledge lin bus

软件UART示例 两个完整的例子,一个用PCA为波特率发生器的C语言程序和一个用定时器0为波特率发生器的汇编语言程序. 适用于下列器件 C8051F000C8051F001C8051F002C8051F005C8051F006C8051F010C8051F011C8051F012C8051F015C8051F016C8051F017C8051F220C8051F221C8051F226C051F230C8051F231C8051F236-Software UART Examples of two complete example, a baud rate generator with PCA for the C language program and a use timer 0 baud rate generator for the assembly language program. C8051F000C8051F001C8051F002C8051F005C8051F006C8051F010C8051F011C8051F012C8051F015C8051F016C8051F017C8051F220C8051F221C8051F226C051F230C8051F231C8051F236 applies to the following devices

embeded in keil51

温度传感DB18B20七段显示实验

用于C51上的modbus协议，经测试可运行，但还不完善-C51 for the Modbus protocol, the tests will be run, but still not perfect

增加ASCII.C的一个ASCI码(7F),用于虚拟按键用 修改UART串口的命令解析程序，修改RTC的pcf8563中断部分。 精简IIC和smart_timer代码,添加define.h的宏定义。 修改system.c里的消息堆栈的宏定义 增加ii.c函数,支持对eeprom的打包 增加由PLD或者GPIO输出的模拟UART，在6个CLOCK下速度为57.6K 增加消息的优先级功能，消息类型的前4位为消息的优先级，后4位为消息的类型 试用于初学单片机并且想更上一层楼的，或者有些基础，想减少工作量的。-an increase ASCII.C the ASCI code (7F) for the virtual keys with serial UART to amend the order analytic procedures, the revised RTC pcf8563 interruption part. IIC and smart_timer streamline code, add the definition of Acer define.h. The revised system.c news stack macros increase II.c function, support for EEPROM packaged increase from the PLD or GPIO output analog UART, in the next six CLOCK speed of 57.6K news of the priority function of the type of information before news of the four priority levels after four types of information on the trial beginner to a higher level and SCM, or some foundation, we want to reduce the workload.

本程序将指定的显示缓冲区送显，并将读取的键值送显。 入口参数：显示缓冲区首地址在SADR中,要显示的位数在CNT中。 出口参数: 无。-This procedure will be sent to the designated display buffer significantly, the key will be sent to a significant reading. Entrance parameters: the first address in the display buffer SADR, it is necessary to show that the median of the CNT. Export parameters: None.

关于msp430单片机的一些 自己收集的一些有需要的请下载-MSP430 MCU on some of his own collection of some of those in need, please download