登录
首页 » 图形图像 » The program is used to judge whether a .jpc document is on the DCI standard.

The program is used to judge whether a .jpc document is on the DCI standard.

于 2022-03-24 发布 文件大小:4.40 MB
0 155
下载积分: 2 下载次数: 1

代码说明:

可用于判断JPEG2000图像(.jpc)文件是否符合DCI(数字电影工业规范)标准。 使用方法:敲入命令行test.exe ***.jpc即可-The program is used to judge whether a .jpc document is on the DCI standard.

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • 基于MemDC双缓存绘技术的温度计
    在VC6.0上实现简单的动态温度计,利用MFC向导创建基于对话框的工作空间,创建MemDC类,实现双缓存绘图,
    2022-10-19 16:00:03下载
    积分:1
  • 该示例中的字模数组均由“点阵字模工具”生成,你可以用你自己需要的点阵信息来 替换示例中的字模信息,注意字模大小要一致,否则显示会出问题。...
    该示例中的字模数组均由“点阵字模工具”生成,你可以用你自己需要的点阵信息来 替换示例中的字模信息,注意字模大小要一致,否则显示会出问题。-example of the array are Fonts "Matrix Printer tool" generation, you can use your own information needs to replace dot matrix examples of Fonts information, attention Fonts size to be consistent, otherwise show will be problems.
    2023-09-08 18:35:03下载
    积分:1
  • 识别百度的验证码VB源码,了解如何识别网页上的数学
    识别百度的验证码VB源码,了解如何识别网页上的数学图片-identification verification VB source code and understand how to identify the mathematical website Photo
    2022-11-11 09:50:04下载
    积分:1
  • ADI BLACKFIN 与MICRON 的CMOS SENSOR 的IIC驱动程序
    ADI BLACKFIN 与MICRON 的CMOS SENSOR 的IIC驱动程序
    2023-05-19 16:40:04下载
    积分:1
  • 弹性动力学工具箱是MATLAB工具箱的波传播模型
    The ElastoDynamics Toolbox is a MATLAB toolbox to model wave propagation in layered media. It is based on the direct stiffness method and the thin layer method [10, 12]. The toolbox can be used to solve a variety of problems governed by wave propagation in the soil: Site amplification Site amplification is an important issue in the assessment of the seismic hazard at sites where the top soil layers are particularly soft. In such cases, the seismic motion at the surface can be much higher than the outcrop motion due to resonance of the soft layers-This chapter describes how to start using the ElastoDynamics Toolbox (EDT) for MATLAB. The chapter is organized as follows: About the ElastoDynamics Toolbox (p. 1) The ElastoDynamics Toolbox for MATLAB is briefly introduced. Obtaining and installing EDT (p. 1) This section explains where to get EDT and how to install it. Terms of use (p. 3) The terms and conditions to use of EDT are summarized. It is shown how to re
    2022-02-13 02:45:17下载
    积分:1
  • 泊松表面重建代码
    完整的泊松表面重建算法的,实现的是Hoppe2013年SIGG的一篇文章,这篇文章是基于2006年工作的基础改进性的工作,源码清晰易懂,有注释。
    2023-03-28 10:40:03下载
    积分:1
  • A good target detection procedures, the use of OpenCV and VC++ Programming, is c...
    目标检测的好程序,利用OpenCV和VC++编程,是目前比较流行的方法,效果很好的源码!-A good target detection procedures, the use of OpenCV and VC++ Programming, is currently the more popular methods, the effect of a very good source!
    2022-04-13 01:44:02下载
    积分:1
  • purpose computes PSNR between two raw YUV i mages compile gcc
    purpose computes PSNR between two raw YUV images compile gcc -g -o cmp_yuv cmp_yuv.c -lpgm -lpbm -lm -purpose computes PSNR between two raw YUV i mages compile gcc-g-o cmp_yuv cmp_yuv.c- lpgm- lpbm- lm
    2022-11-18 13:35:03下载
    积分:1
  • 水质拟合工具
    自已编写的一个水质检测数据拟合工具,用C++Builder编写,能够根据输入的数据进行拟合计算,生成相应的图表,并打印,很实用的工业工具
    2022-11-22 13:10:03下载
    积分:1
  • 浮动水平线算法绘制网格表面程序
    浮动水平线算法绘制网格表面程序-breath-5, a program file to show that I will be my last set of five procedures is described.
    2022-01-25 21:33:25下载
    积分:1
  • 696516资源总数
  • 106914会员总数
  • 0今日下载