MSP430 CRC算法的实现 （基于msp430x16x）

RF905无限模块的说明文档 pdf，v3.0.-RF905 wireless transit function chip，datasheet，pdf，vision 3.0

本地机使用ATDT命令拨号,远程机设为自动响应方式,即可进入联机方式, 进行终 端通信.在联机方式下,按PageUp键上载文件,按PageDn键下载文件,Ctrl-O呼出主菜单, 退出联机方式使用Ctrl-D键.退出终端仿真器主程序使用TC编写.终端方式为VT100.-Local machine using the ATDT command dial, the remote machine is set to automatically respond to the way, you can enter the line for terminal communication. In-line mode, press PageUp key to upload files, download the file by PageDn keys, Ctrl-O exhaled main menu , quit-line use Ctrl-D keys. withdraw from the terminal emulator to use TC to prepare the main program. terminal for VT100.

There a lot of program can be used it is wonderful

可以进行单片机等电路仿真调试 可以进行单片机等电路仿真调试

6段数码管分别显示，时，分，秒，四个按键，K1（P0.0），K2（P0.1）， K3（P0.2），K4（P0.3），四个按键用来调时间的，按下K1，所有位都清零显示，然后按下K2，秒在闪烁，继续按K2分闪烁，不段地按K2 秒--分--时切换着闪烁，在某位闪时按下K3相应位加一，确认调整，按K4，取消调整再按K1。在K1按下以后才有调时的功能，如果K1没有按下，按别的键没有反映。这为了在加点按键功能留着用 -6 respectively of the digital control, when, minutes and seconds, four keys, K1 (P0.0). K2 (P0.1), K3 (P0.2), K4 (width), the four keys to the transfer time, press the K1, All spaces are reset, then press K2, the scintillation seconds, according to K2 pm flickered. not according to K2 of seconds-- minutes-- when switching to flicker in certain press the flash-K3 corresponding increase in a confirmed adjustment by K4, then canceled K1 adjustment. K1 in the press will only be made after the transfer of function, if K1 pressed by other key is not reflected. This points to the function keys used Retention

MSP430X41X子程序，希望对大家学习430单片机有用... ... ... ...!-MSP430X41X subprogram, and they hope to learn from U.S. 430 Singlechip useful ... ... ... ...!

功能描述： 利用AT89S51单片机的T0、T1的定时计数器功能，来完成对输入的信号进行 频率计数，计数的频率结果通过8位动态数码管显示出来。要求能够对2－40KHZ 的信号频率进行准确计数，计数误差不超过2/1-Functional Description: Using AT89S51 MCU T0, T1 timing counter function, to complete the input signal frequency counting, counting the frequency of 8 resulted in the adoption of dynamic digital tube display. Request to the 2-40KHZ signal frequency accurately count, counting error of less than 2/1

18b20的仿真实例，希望能帮做一些初学者，-18b20 the simulation example, I hope to do something to help beginners,

该书详细的介绍了msp430下载线的制作，并且附带详细的程序-The book detailed introduction of the MSP430 to download the production line, and attached to the detailed procedures

本人做的一款LED控制程序，具有温度，日期，每天8次定时开关，使用期限设定，密码保护等等。-new LED control procedures, the temperature, date, the 8th day timer switch, the deadline set use, password protection and so on.