扩展程序的功率放大器、单片机AT89C2051接收..

C语言编程宝典。开发c51单片机的工具书-C language programming book. C51 MCU development tool

实现对ADE7758电能芯片的读写和校准,8051单片机,通过PC对电参量进行校准-Realize on-chip ADE7758 energy literacy and calibration, 8051, through the PC on the electrical parameter calibration

系统讲解了51单片机,实用于初学者,可以很快入门-system on the 51 microcontroller, in the practical and beginners can quickly entry

做的一个FFT算法原程序与大家共享，内有较祥细的说明-do an FFT algorithm for the original procedures and share, compared with a wound Note

是用51单片机检测色度色差的算法和具体实现的代码-is 51 Single-color and color algorithm to achieve specific code

这段程序是用在一款七彩灯红外遥控解码程序里,单片机使用PIC12F629,软件模拟三路PWM输出驱动红绿蓝LED分八组共24个LED,实现单LED渐明渐暗,两LED一明一暗,七彩等九种花样.有断电记忆功能.如下是解码程序.-This procedure is used in a colorful light infrared remote control decoding procedure, the single-chip using the PIC12F629, the software simulation of three-way PWM RGB LED output driver in eight groups of 24 LED, single LED gradually dimming out, First one out of two LED dark, colorful patterns, such as nine. have power memory function. decoding procedure is as follows.

用交叉串口线连接两块单片机进行双机通信，扫描到有键按下时，键值发送出去，另一块板收到后以0-F方式显示在数码管上。-With cross-serial cable to connect two pairs of aircraft communications microcontroller to scan that there are key is pressed, the key to send out another one after the board received 0-F are displayed in the digital pipe.

单片机的程序，实现的是采灯的设计与实现功能-SCM procedures and achieve the mining lamp design and implementation functions

C51与HT9170和HT9200接口程序(双音多频)-C51 with HT9170 and HT9200 interface program (DTMF)

本设计以P89V51RD2FN单片机为电动小车的控制核心，采用MSA-LD2.0倾角传感器实时测量跷跷板的倾斜角，用ST198光电传感器检测黑色引导线监测小车运动。光电传感器和倾角传感器模块把实时测量信号馈送至单片机，利用专用细分芯片TA8435H驱动步进电机，以脉宽调制式斩波方式对步进电机步进角进行细分，控制和调节小车速度。采用增量式PID控制算法确保小车能够达到平衡；用RT128×64M液晶显示时间、角度等参数。经测试表明：小车各项性能指标达到设计要求，能够实现30秒内小车行驶到规定点，并保持跷跷板平衡；在跷跷板一端配重可调整的情况下，小车也能自动找到平衡点并保持跷跷板平衡。-The single-chip design for the electric car P89V51RD2FN control of the core, the MSA-LD2.0 seesaw angle sensor real-time measurement of the tilt angle, the detection of black ST198 photoelectric sensor to monitor vehicle movement and guide lines.Photoelectric sensors and angle sensors in real-time measurement module to feed the signal to the microcontroller, using a dedicated sub-chip stepper motor driver TA8435H to PWM chopper-type stepper motor on the sub-stepping angle, control and regulation vehicle speed. The use of incremental PID control algorithm to ensure that the car can achieve balance with LCD RT128 × 64M time, angle and other parameters.After the test showed that: the performance car