自动售货机的Verilog

用Verilog实现一个基于Mesh拓扑结构的路由器网络(Using Verilog to implement a router network based on Mesh topology)

时间同步后即可确定每帧数据的起始位置，这样就能完整的截取下每一帧。但是，数据中还带有频偏信息。在常规的通信系统中，多普勒很小仅仅会带来很小的频偏，但是在大多普勒的情况下，频偏将非常大，20马赫的速度将会带来将近34K的频偏。因此，如何很好的纠正频偏即为本系统的难点。 OFDM中，我们将大于子载波间隔倍数的频偏称为整数倍频偏，而将小于一个子载波间隔的频偏称为小数倍频偏。频偏矫正精度只要能保证小于十分之一倍的子载波间隔，频偏就不会对均衡和解调造成影响。本文中我们借鉴这种思想，由于硬件资源限制，我们将在接收端做64点FFT，即相当于将频域划分为64份，我们将小于 的频偏称为小数倍频偏，将 整数倍的频偏称为整数倍频偏。本程序即基于SCHIMDL经典方法完成小数倍频偏纠正(After time synchronization can determine the starting position of each frame data, so you can complete the interception of each frame. However, in the data with frequency information. In conventional communication systems, doppler small will bring only small deviation, but in the case of most of the doppler, frequency PianJiang is very large, 20 Mach speed will lead to deviation of nearly 34 k. Therefore, how to good to correct deviation is the difficulty of this system. OFDM, we will be bigger than the sub-carrier spacing ratio of frequency deviation is called the integer frequency offset, and the interval will be less than a child carrier frequency offset is called decimal frequency doubling. Deviation is less than one over ten times as long as can guarantee accuracy of sub-carrier spacing, deviation will not affect balance and demodulation. This article, we draw lessons from the idea, due to the limited hardware resources, we will do 64 points FFT at the receiving end, which is equ)

单片机和FPGA的通信程序，发送5个数，传输稳定，可以自行修改可一次传多个数(MCU and FPGA communication program, send five the number of stable transmission, you can modify the number may be more than one pass)

利用FPGA开发软件 进行rs编码的仿真 模拟RS编码的过程步骤(rs code in FPGA)

代码由Verilog语言编写，可以实现HDLC协议，主要由发送模块、接收模块和cpu接口三个大模块组成，可以替代集成芯片PT7A6525。

基于FPGA状态机实现的I2C Verilog工程文件，在多个项目中运用检验，非常可靠，有详尽的注释，可读性非常清晰，需要的可以下载

SDIO slave verilog code

This programa execute calc of CRC by use a table.

EGO_1流水灯显示代码步骤过程全都有适合初学者练手(EGO_1 nxoiaocijpwjcpoewopvkpowevko)

说明：  FPGA程序的top.v文件，主要实现DDS信号发生器功能，通过定时器，可简单实现输出幅值无极跳变(FPGA procedures top.v documents, the main function of DDS signal generator, through the timer can be simple to achieve the output amplitude wuji hopping)