24 high

s24193 液晶ARM，8051驱动程序！-s24193 LCD ARM, 8051 driver!

18B20的程序 大家分享 刚刚接触的可以看看 挺有帮助的-18B20 procedures to share with you just contact can look at quite helpful

MCS-51单片机实用子程序库1，WORD文档-MCS-51 microcontroller practical for a subroutine, the Word document

用交叉串口线连接两块单片机进行双机通信，扫描到有键按下时，键值发送出去，另一块板收到后以0-F方式显示在数码管上。-With cross-serial cable to connect two pairs of aircraft communications microcontroller to scan that there are key is pressed, the key to send out another one after the board received 0-F are displayed in the digital pipe.

当你进入线路板（PCB）这个行业后，首要面对的就要了解行业术语， 为此特别整理了包括大陆，台湾，香港等多位行业专家编写，修定， 再修定的PCB行业方方面面的术语和词汇。将网上流传的多种版本进行 了修正、统一和分类，更合理的介绍了线路板（PCB）专业术语。方便 大家查阅。-When you enter the circuit board (PCB) in the industry, the primary face and need to know about the industry jargon, for this special finishing, including mainland China, Taiwan, Hong Kong, etc. to prepare a number of industry experts, the revised and then revised all aspects of PCB industry terminology and vocabulary. Will be a variety of popular online version of the amendment, unity and classification, a more reasonable introduction PCB (PCB) professional terminology. Convenient access to everyone.

本程序实现74HC165芯片的使用功能，在51单片机上实现-this program is to tell how to use 74hc165 on 51 single chip controlere

单片机控制步进驱动，S1为启动，S2为停止，S3为加一，S4为减一-Single-chip stepper drive control, S1 for the launch, S2 to stop, S3 for the plus-one, S4 for by one

基于51单片机的公交车报站系统程序 基于51单片机的公交车报站系统程序-Based on 51 MCU bus stop announcement system program

MCS-51单片机有5个中断源，其中两个是由-INT0、-INT1引脚输入的外部中断源；另外三个是内部中断源即由T0、T1的溢出引起中断和串行口发送完一个字节或接收到一个字节数据引起中断。触发外部中断有两种方式，即下降沿引起中断或低电平引起中断。当编程TCON中的ITi（i=0、1）为1时，则引起触发的方式为边沿触发方式，反之(ITi=0)为低电平触发方式。每个中断源的中断请求能否得到响应要受两级“开关”的控制，即一个总“开关”-MCS-51 single-chip has five interrupt sources, two of which are by-INT0,-INT1 pin input external interrupt source the other three internal interrupt sources from the T0, T1 overflow caused by the disruption and serial port sending or receiving end of a byte to a byte of data caused by interruption. Triggered external interrupt has two modes, namely, falling edge or low-level disruption caused disruption caused. When programming TCON in ITi (i = 0,1) for the 1:00 has been the subject of a way to trigger the way to the edge of the trigger, on the contrary (ITi = 0) for low-level trigger mode. Each interrupt source interrupt request can be subject to levels in response to

用单片机配置FPGA，英文，不用说了吧，呵呵，快下吧-MCU FPGA configuration, English, needless to say, all right, what are you fast