登录
首页 » 嵌入式芯片 » DIY示波器大家都想要的我现在上传给大家

DIY示波器大家都想要的我现在上传给大家

于 2022-03-18 发布 文件大小:358.93 kB
0 149
下载积分: 2 下载次数: 1

代码说明:

DIY示波器大家都想要的我现在上传给大家-Oscilloscope DIY all the information that many people are currently engaged in this kind of DIY, From the information I hope to help these people!

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • kei carm lpc2103 examples of good things
    kei carm lpc2103 例子 好东西-kei carm lpc2103 examples of good things
    2023-04-07 06:30:03下载
    积分:1
  • Development Environment: ADS 1.2/SDT 2.51GUI test, because there is no touch scr...
    开发环境:ADS 1.2/SDT 2.51 GUI测试,由于没有触摸屏,所以将触摸屏的代码给屏蔽了; 请将FS44B0II开发板连接好交叉网线、直连串口线、电源, 并连接好G57液晶屏,同时还要连接好背光电源; 然后在BIOS的命令窗口里面敲netrun命令; 点击FS44B0_G57_uCGUIuC-GUIFS44B0_G57_uCGUI_DataDebugRel目录下: 批处理文件FS44B0_G57_uCGUI.BAT 下面你就可以看到液晶屏上面显示优龙标志 它会延时一两秒中进入下一个画面,逐步延时GUI的各项功能,请耐心观看; -Development Environment: ADS 1.2/SDT 2.51GUI test, because there is no touch screen, it will be touch screen to shield the code Please FS44B0II development board to connect a good cross-network lines, direct serial lines, power supply, and connect a good G57 LCD screen, at the same time, good backlight power supply connection and then in the BIOS command window knock netrun order Click FS44B0_G57_uCGUIuC-GUIFS44B0_G57_uCGUI_DataDebugRel directory: batch file FS44B0_G57_uCGUI.BAT below you can see the LCD screen above shows excellent signs that it will delay Liuzhou 1 two seconds to enter the next screen, and gradually delay the GUI features, please be patient watch
    2022-02-06 06:38:46下载
    积分:1
  • 2410 startup code
    2410 启动代码-2410 startup code
    2022-05-31 20:59:50下载
    积分:1
  • 三星S3C2440 IIS控制器驱动程序
    三星S3C2440 IIS控制器驱动程序 -Samsung S3C2440 IIS controller driver
    2022-02-05 12:38:31下载
    积分:1
  • ARM基础知识,我刚找到的。 和大家共同分享下
    ARM基础知识,我刚找到的。 和大家共同分享下-ARM basic knowledge, I have just found. And the U.S. share of
    2022-06-15 19:58:03下载
    积分:1
  • AT91SAM7 SWI, Remap, GPIO, PIT and stdio Example ( Gamma )
    AT91SAM7 SWI, Remap, GPIO, PIT and stdio Example ( Gamma )
    2022-07-19 20:32:06下载
    积分:1
  • 基于EasyARM1138的光标修动修改程序
    基于EasyARM1138的光标修动修改程序-Based on revised EasyARM1138 cursor moving an amendment to the procedure
    2022-04-23 18:24:01下载
    积分:1
  • STM32F4发现USB测试
    本程序是用虚拟USB将stm板连接到PC机上的程序。在这种情况下,它使用USRT模式或USB主机。
    2022-06-21 01:43:47下载
    积分:1
  • 在DMA模下的SPI通信
    这是一个基于stm32的程序文件,通过DMA方式的spi通信,部分功能按自己需求自己添加,部分引脚按自己情况稍加修改。
    2022-03-02 05:35:10下载
    积分:1
  • S3C2410处理器集成的USB DEVICE设备控制驱动程序,实现PC端与实验板USB设备进行数据发送与接收。...
    S3C2410处理器集成的USB DEVICE设备控制驱动程序,实现PC端与实验板USB设备进行数据发送与接收。-S3C2410 processor integrated USB DEVICE device control driver-side with the experimental realization of PC board USB devices to send and receive data.
    2022-03-17 14:07:20下载
    积分:1
  • 696516资源总数
  • 106914会员总数
  • 0今日下载