430code

系统can地址为550,用于can系统测试,应用T0定时器每隔1s向can总线发送一组数据:数据长度为8个字节, 首字节为05H,第二个字节为累加变量,每秒钟数值增加1,-system can address 550 for the test system can, Application T0 1s to every timer can send a bus of data : data length of 8 bytes the first byte of 05H, the second byte of cumulative variable, an increase in value per second.

控制电机运动的G代码程序,如果对G代码不清楚,请先看懂G代码,然后再看本程序.-Control motor movement, G code program, if the G code is not clear, please understand G code, and then look at the procedures.

英飞凌C166之XC164CS开关SWITCH程序-Infineon C166 procedures of XC164CS switch SWITCH

单片机下载工具STC-isp-v3.93版本解压即用绿色软件-Download tools Singlechip STC-isp-v3.93 versions of decompression that is green software

采用步进电机模拟洗衣机电机，实现上水、浸泡、洗涤、漂洗、甩干等过程。洗涤分弱洗、轻洗、强洗；可设定3级水位设定，每级水位均设定水位下限（值自定）；可选择漂洗次数（3~5次）。使用键盘进行流程及参数设定及自动存储流程，设定暂停键，可暂时停止洗衣机的工作，恢复后按原设定程序继续进行，同时设定停止键，可终止洗衣机的工作，并在LED或LCD上显示当前流程。-Simulation using stepper motors washing machine motor to achieve Sheung Shui, soaking, washing, rinsing, drying and other processes. Washing sub-weak wash, light wash, strong wash can be set to three water level settings, set the water level in each grade level were lower (the value of self-set) optional rinsing times (3 ~ 5 times). Using the keyboard processes and parameter settings and automatic memory processes, set pause button to temporarily suspend the work of washing machines and restore original settings after the process to continue at the same time set the stop button, may terminate the work of washing machines, and LED or the LCD displays the current process.

】本文介绍了一个使用单片机和CPLD联合控制步进电机的方案。首先阐明步进电机的工作原理及控制方法，然后 提出了系统的软硬件设计框架，详细讨论了单片机和CPLD的逻辑接口问题和交换数据的协议，以及用状态机来设计脉冲分配器 的方法。-This paper describes a combined use of SCM and CPLD stepper motor control program. First of all, to clarify the working principle of stepper motor and control method, and then put forward a system of hardware and software design framework for a detailed discussion of the MCU and CPLD logic interface issues and data exchange agreements, as well as the use of state machine design Pulse Distributor methods.

　单片机实现非接触式IC卡读写 哟详细的原理图和代码！！！！！！！！！！！！！！！！！1-Singlechip realize non-contact IC card reader yo detailed schematics and code! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! 1

8051模拟板买不起的朋友可以和他们一起买

目前所做的一套卫星测距系统应用到CAN2.0A协议,由于CAN现在多为军用,因此资料很少,这个是CAN控制器SJA1000同C51弹片机的通信程序,站长参考下吧.-doing a satellite location system application to CAN2.0A agreement, CAN over to the military now, very little information, this is the SJA1000 CAN controller with shrapnel C51 machine communication procedures, head of reference under it.

MSP430F247系列的C源代码，，好东东哦-MSP430F247 series of C source code, and good Dongdong Oh