Atmega169usart drive

NRF24E1的AD模块，其中包含如何加入ISD51代码进行用户代码的调试-NRF24E1 the AD module, which includes instructions on how to join ISD51 code debugging user code

基于320×240图形点阵液晶与51单片机的接口设计程序。采用C51编程制作。-Based on 320 × 240 dot-matrix graphic LCD interface with 51 single-chip design process. The use of C51 produced programming.

数码时钟显示，用8位LED软件译码动态显示，P0为字段码,P2为位选码，数码管共阳， key0为位选键；key1为加“1键；key2为减“1”键。-Digital clock display with 8 LED dynamic display software decoding, P0 code for the field, P2 election code for the digital, digital tube were positive, key0 bond election for the position key1 to add " 1 button key2 to reduce the" 1 " button.

具有固定的“红灯―绿灯”转换间隔，并自动切换。它们一般由“通行与禁止时间控制显示、红黄绿三色信号灯和方向指示灯”三部分组成。在交通灯的通行与禁止时间控制显示中，通常要么东西、南北两方向各50秒；要么根据交通规律，东西方向60秒，南北方向40秒，时间控制都是固定的。交通灯的时间控制显示，以固定时间值预先“固化”在单片机中，每次只是以一定周期交替变化。-having fixed the "red light-green light" switch partitions, and automatic switching. They are generally from "prohibiting access and time control, red-yellow-green lights and direction indicator" is composed of three parts. Traffic lights in the passage of time and prohibit control indicates that things are usually either the north-south direction of the two 50 seconds; either on the basis of traffic laws, an east-west direction 60 seconds, 40 seconds north-south direction, the time control are fixed. Traffic lights to the time control, a pre-fixed time value "cured" in SCM, each is a certain cycle alternation.

利用单片机设计一个显示温度的系统，主要采用的是静态显示的方式-The use of microcontroller design a show that the temperature of the system, mainly in a static display mode

用过采样和求均值技术提高模数转换器的分辨率.pdf-----针对目前单片机内嵌的模／数转换器的分辨率太低，而外接高分辨率成本又太高的情况，提出了用“过采样和求均值”的技术来使在有用的测量频带内的信噪比得到改善，从而提高测量的分辨. 率。并利用 60 - 7 0 /对其结论进行仿真，且在单片机上予以实现，结果表明测量分辨率明显提高。-Sampling and averaging techniques used to improve the resolution of ADC. Pdf----- targeted at the embedded microcontroller A/D converter resolution is too low, while the external high-resolution costs are too high situation, put forward with " Oversampling and Averaging" technology to make useful measurements in the frequency band signal to noise ratio to be improved, thereby enhancing the measurement resolution. rate. And a 60- 7 0/simulation of its conclusions, and in the SCM to be achieved, results show that the measurement resolution has improved significantly.

提供一个小弟的程序,有点笨,请各位看后,不要见笑.-provide a younger procedures, a bit stupid, you see, not laughed at.

Keil C 编程的手写板-Keil C Programming 5270

TLC5615是TI公司的10位D/A转换芯片，DIP-8封装，数据为串行方式，简单好用。内有该芯片的KIEL C51源代码，希望和大家共享。-TLC5615 is TI

是关于sd卡的接口电路图以及pcb封装原理图 是sd卡驱动者重要的资料-Is on the sd card interface circuit and the pcb schematic package sd card driver is important information