MSP430 I2C interface module with EEPROM assembler

W3100是WIZnet公司专门为以太网互联和嵌入式设备推出的硬件TCP／IP协议栈芯片，其硬件TCP／IP协议栈包含了TCP、UDP、IP、ARP和ICMP协议，这是sever例子源码-WIZnet W3100 is designed for the Internet and Embedded Ethernet equipment introduced hardware TCP/IP protocol stack chips, and hardware TCP/IP protocol stack includes TCP, UDP, IP, ICMP and ARP agreement sever example of this is FOSS

C51实现的FAT32文件系统-C51 of the FAT32 file system

用WAVE6000开发环境写的电子钟程序-WAVE6000 development environment used to write procedures for electronic bell

基于单片机c8051f020的模数转换，数模转换应用实例-C8051f020 based on single-chip analog-to-digital conversion, digital-to-analog converter application

P1.7～P1.0接发光二极管L8～L1，要求利用单片机内部定时器1，按方式1工作，每0.01秒T1溢出中断一次。要求编写程序模拟时序控制装置。开机第1秒钟L1、L3亮，第2秒钟L2、L4亮，第3秒钟L5、L7亮，第4秒钟L6、L8亮，第5秒钟L1、L3、L5、L7亮，第6秒钟L2、L4、L6、L8亮，第7秒钟8个发光二极管全亮，……一直循环下去。fosc=11.0592MHz-P1.7- P1.0 then LED L1 to L8, by using a timer internal microcontroller, a work by the way, every 0.01 seconds T1 interrupted an overflow. Simulation prepared timing control device. Boot 1 seconds L1, L3- liang, two seconds L2- L4, L5 three seconds, L7- liang, 4 seconds L6, L8-liang, 5 seconds L1, L2, L5, L7- liang, 6 seconds L2, L4, L6, L8- , 7 seconds 8-LED whole ... has been the cycle continues. 11.0592MHz fosc =

MSP430F449的LCD使用(代码和硬件)[芯片类]-MSP430F449 the LCD use (code and hardware) [chip category]

直流电机转速测控，并实现语音报速，而且在LCD上显示当前设置的速度-DC motor speed measurement and control, and realize al-speed voice, but also in LCD displays current settings of the speed of

汇编源代码，红外应用源程序集，主要 是关于红外探测技术的。-compilation of source code, source Set infrared applications, mainly for infrared detection technology.

编译环境是KEIL,仿真环境是PROTEUS,控制彩灯的闪烁，利用51单片机，内含Keil C51教程可以使大，家了解彩灯的设计同时学习KEIL。-Compiler environment is KEIL, simulation environment is PROTEUS, control of the flashing lantern, using 51 single-chip, including Keil C51 Guide can enable the home to understand the design of lanterns at the same time learning KEIL.

4x4矩阵键盘数码管显示键值,按下4*4矩阵键盘，可以看到数码管的最后一位显示了对应按健的健值.-4x4 matrix keypad LED display keys, press 4* 4 matrix keyboard, you can see the last one shows the digital control of the health value of health should be.