基于ARM7的开发板的键盘驱动程序，文件里有程序的详细注释，对与在此基础之上的二次开发非常方便...

用LPC2136测试三维加速度传感器mma7456,用模拟I2C实现通信-Three-dimensional acceleration sensor with the LPC2136 test mma7456, simulated I2C for communication

杭州利宇泰公司的基于44B0的ARMSys开发板上的大量源代码，包括ADC、ARP、彩色LCD、外部中断、以太网底层函数、FAT16文件系统、Flash ROM、GUI软件包、Helloworld程序、IIC接口、扫描键盘、Ping程序、44B0内置RTC示例、SDRAM接口、定时器示例、触摸屏示例、UART示例和uC/OS-II的移植、应用（包括多任务、任务间通信、中断服务程序）、UDP数据传输、USB固件编写等程序代码和工程。一次性共享给大家使用。可以作为其他samsung44B0开发板上应用程序的下载。-Lee Yu-tai Hangzhou-based company 44B0 ARMSys development board of a large number of source code, including the ADC, ARP, color LCD, external interrupts, Ethernet bottom function, FAT16 file system, Flash ROM, GUI packages, Helloworld procedures, IIC interfaces, scanning keyboard, Ping procedures 44B0 built-in RTC example, SDRAM interface, timers example, the touch screen example, UART examples and uC/OS-II transplants, applications (including multitasking, inter-task communication, interrupt service routine), the UDP data transmission, USB firmware preparation procedures code and engineering. One-time use for everyone to share. As other samsung44B0 development board application downloads.

SDT环境下，基于S3C4510的flash使用，可用-SDT environment, S3C4510 based on the use of the flash can be used

师兄给了块开发板，开始学习，先在上面跑LED，测试代码，网上找的头文件移植，免得自己写了，先裸跑，之后再上Linux。

FreeRTOS + Lwip For MCB23-FreeRTOS+ Lwip For MCB2300

智能车设计报告哦，很好用的东西，我也希望同仁也能提供一些有用的资料共享。-Intelligent Vehicle Design Report Oh, very good with things, I hope colleagues can also provide some useful information to share.

用Keil C语言编写的EZ-USB CyC768013芯片 slave FIFO模式的固件程序-Keil C language using the EZ-USB CyC768013 chip slave FIFO mode firmware

ADC7843驱动-ADC7843 drive

汇编编写的ARM启动代码，包括中断向量、运行域搬移、堆栈设置等代码的演示，还包括了一个scatter文件，注释详细。麻雀虽小五脏俱全，对于ARM编程的初学者，有助于理解ARM的代码链接和生成，以及启动过程。代码使用ADS1.2编写，可以直接运行查看。-Compilation prepared by ARM startup code, including the interrupt vector, run the domain move, stack setup code demonstration, but also a scatter file, comments in detail. Sparrows are small is a fully-equipped, for ARM programming for beginners, help to understand the link ARM code and generation, as well as the boot process. Code uses ADS1.2 prepared, you can directly run the Show.

本程序是用虚拟USB将stm板连接到PC机上的程序。在这种情况下，它使用USRT模式或USB主机。