Optical Power Meter with C8051F060 development program prepared by the C51

Keil C51对8254进行操作的源程序-Keil C51 8254 to operate a source

我自己整理的单片机4*4键盘最简扫描算法，相当精炼。-I sort of SCM 4* 4 keyboard the most simple scanning algorithm, very refined.

此代码是我们在单片机来控制CPLD记数,然后读出并转换数据,精度很高,在我们学校的电子设计大赛上还获的了二等奖-this code is in MCU to control CPLD counting, and then read out the conversion of data, the accuracy is high, In our schools Electronic Design Competition was also a second prize of

数字语音回放系统,通过AD采样,单片机算法处理,DA送出放大-Digital voice playback system, through the AD sampling, single-chip microcomputer algorithm treatment, DA Submit to enlarge

usb编程器的全部资料，包括上位机程序及下位机源程序 支持编程器类型 1,多种并口（可以自定义）编程器（并口串行） 2,USBPROG编程器（usb串行） 3,并口并行编程器 4,usbasp 扩展功能 1,串口调试,超级终端 特色： 1,速度较快(16k程序): 并口 读11秒 写11秒；USBPROG读2秒 写2秒。 2,USBPROG根据目标cpu自动调整三种下载速度(8k,187.5k,375k) 3,支持自定义ATMEL全系列cpu(avr+S5x 系列). 4,支持自定义熔丝信息提示功能 -usb programmer all the information, including procedures and PC-under-source programming support for a similar, multiple parallel port (which can be customized) programming (Serial Parallel Port) 2, USBPROG Programming (usb serial) 3, Parallel parallel programming for four, a usbasp expansion, Serial debugging, the Super Terminal characteristics : a high speed (16k procedures) : Parallel Port Reading 11 seconds was 11 seconds; USBPROG Reading 2 seconds was two seconds. 2, according to the target cpu USBPROG automatic adjustment of the three download speeds (8k, 187.5k. 375K) 3, ATMEL support from the definition of a full range of cpu (avr S5x series). 4. Fuse support from the definition of functional i

通过GPRS的PPP拔号程序,本程序在x86下通过测试-through GPRS PPP dialup procedures, the procedures adopted in x86 tests

I2C总线基本操作函数,及几个对I2C总线接口器件24C04操作的函数。 -I2C bus basic operation function, and several of the I2C bus interface device to operate a function of 24C04.

三相步进电机的三相六拍工作方式，正转的绕组通电顺序：A、AB、B、BC、C、CA、A，反转的通电顺序：A、AC、C、CB、B、BA、B、A。 由于步进电机转子有一定的惯性以及所带负载的惯性，故步进电机的工作过程中不能及时的启动和停止，在启动时应慢慢的加速到预定速度，在停止前应逐渐减速到停止，否则，将产生失步现象。 步进电机的控制问题可总结为两点： 1、产生工作方式需要的时序脉冲； 2、控制步进电机的速度，使它始终遵循加速、匀速、减速的规律工作。 -Three-phase three-phase stepper motor six shot work, is to order the winding power: A, AB, B, BC, C, CA, A, reverse the order of power: A, AC, C, CB, B, BA, B, A. As the stepper motor rotor has a certain degree of inertia, as well as brought about by the inertia load, the stepper motor during the course of work should not start and stop time, start to be slowly accelerated to a predetermined speed, the stop should be to slow down gradually to the stop, otherwise, will result in out-of-step phenomenon. Stepper motor control problems can be summarized in two points: one, resulting in the need to work the timing pulse 2, control the speed of stepper motor, so that it always followed acceleration, velocity, deceleration of the law of the work.

单片机设计， 单片机设计， 单片机设计， -Single-chip design, microcontroller design, microcontroller design, microcontroller design, microcontroller design, microcontroller design,

基于DS12887的多功能电子智能时钟，51控制 LCM-12864-ST7920显示，应用类型齐全。-DS12887-based multi-functional electronic smart clock, 51 control LCM-12864-ST7920 showed complete application types.