功能强大的串口程序，用avr系列的mega16单片机实现

C51的45D驱动程序-C51 45D Driver

利用单片机AT89S51与adc0809设计一个数字电压表，能够测量0－5V之间的直流电压值，四位数码显示，但要求使用的元器件数目最少-AT89S51 with adc0809 use of single-chip design of a digital voltage meter, capable of measuring between 0-5V DC voltage value, four digital display, but requires the use of minimum number of components

一个完整的个人产品开发源代码,包括对单片机STC12C5410的编程(含内部AD采样、自创的内部Flash编程源码等)、LCD1602的驱动编程等。-A complete source code of the individual product development, including single-chip STC12C5410 programming (including the internal AD sampling, create their own internal Flash programming source code, etc.), LCD1602 driver programming.

EMBEDDED SYSTEM FILE SYSTEM TEST

仿真步骤如下： 1、把3个帖子的内容分别保存为51t9py.c,51t9py_indexa.h,5py_mb.h，放在同一目录下，将51t9py.c加入工程编译 2、由于Keil的模拟串口是单字节显示，汉字显示为乱码，所以要加挂RICHWIN或RichView这种会重新刷新显示的中文平台，或手工刷新屏幕，所以请先到 http://www.pchome.net/dl/chinese.htm 下载RichView，安装运行 3、在Keil环境下可以直接按“Ctrl＋F5”键仿真，按“F5”全速运行，切换到在串口依次输入: // 64*.6 426***.5 98*.7 936.3 586.1 4826*.1 9464*.7 64*.6试试:-) 4、按键对应(根据我自己的手机设置的,全部在PC的小键盘操作)： -simulation steps are as follows : 1 and 3 respectively, the content of messages posted on the preservation of 51t9py.c, 51t9py_indexa.h, 5py_mb.h, on the same directory, will join the project 51t9py.c compiler 2, Keil is the simulation of single-byte Serial show , the Chinese showed gibberish, so need to add or RichView RICHWIN this show will re-set the Chinese platform, or manual refresh screen, so please download RichView http://www.pchome.net/dl/chinese.htm to install three operations in Central Keil Habitat can be directly "Ctrl+ F5" key simulation, according to the "F5" running full-speed, switched to the ser

51单片机编程序学习实践经验丰富工程师编写实机通过-51 SCM-programmed study and practice of experienced engineers to prepare real machine through

利用MEGA8同时控制四路分立的单总线设备TH-11数字湿温度传感器，并根据查找表反推出传感器电阻值，显示在LCD12864显示器上。公司内部用机器。-MEGA8 simultaneously control the use of four separate single-bus devices TH-11 digital wet temperature sensor and, based on look-up table against introduction of sensor resistance value, displayed in the LCD12864 display. Within the company with the test machine.

采用ATMEGA16驱动IC是PCF8533,对应LCD为NOIKA 6610,C语言格式。-ATmega16 driver IC is used PCF8533, the corresponding LCD for NOIKA 6610, C language format.

/// ////单端输入，定时启动，由T2定时，选择AIN0.3为ADC0转化通道//////////////// //////single.c/////////////////////////////////// #include "lcd.h"//笔者所写的LCD显示头文件，具体见LCD章节 /*若读者没有条件使用"lcd.h"的各显示和键盘函数,则可在lcd.h文件中如下定义:-/////// Single-ended input, time to start, by the T2 timer, select AIN0.3 for ADC0 conversion channel ////////////////////// single. c ///////////////////////////////////# include

8051f02x 单片机的实用排序子程序。-Singlechip 8051f02x practical sort subroutine.