单片机的花卉，单片机可以用89C52单片机音乐键。

这是一个功率计参数表格的程序，有兴趣的朋友可以看看，脉冲式的-This is a power parameters forms the proceedings, interested friends can see that the pulse

功能描述： 利用AT89S51单片机的T0、T1的定时计数器功能，来完成对输入的信号进行 频率计数，计数的频率结果通过8位动态数码管显示出来。要求能够对2－40KHZ 的信号频率进行准确计数，计数误差不超过2/1-Functional Description: Using AT89S51 MCU T0, T1 timing counter function, to complete the input signal frequency counting, counting the frequency of 8 resulted in the adoption of dynamic digital tube display. Request to the 2-40KHZ signal frequency accurately count, counting error of less than 2/1

温度控制器：AT89C2051做数据处理和显示；18B20做测温-temperature controller : AT89C2051 do data processing and display; 18B20 do Temperature

EM78P153中文手册，EM78P153堪称最便宜的单片机，还不到二块钱一片。-EM78P153 Chinese Manual, EM78P153 rated the cheapest single-chip, less than a 2 money.

基于8051单片机的遥控电风扇的红外发射源程序-8051-based remote control of the infrared emission source fans

本文章介绍了一种AD值的线性化方法。可以应用于单片机系统的设计开发当中。在系统的硬件设计方法上，使用温度补偿的方法，使得AD转换值可实现线性化，从而可以减少了单片机软件开发当中进行非线性数据的线性化处理。-This article introduces a AD value of the linear method. Can be applied to the design of single-chip microcomputer system development. The system

利用简单的原件自制MSP430的JTAG下载器，适合各种MSP430的单片机，适合单片机爱好者-Original self-made using simple MSP430

利用89S52为核心实现的IDE-USB转接器 现在已经实现了主要功能：可以读取文件和复制文件。不支持格式化硬盘功能。 不过速度比较慢，我从本地硬盘复制文件到移动硬盘里去，速度只有50KBytes/S， 因为单片机速度不快，内存又少，USB1.1的速度也不快。另外，代码写得不够好 压缩包内有线路图-89S52 realize use as the core of the IDE-USB adapter now realize the main function: You can read the files and copy files. Reformat your hard disk does not support the function. More slowly, however, I copy files from the local hard disk to a mobile hard drive into a speed only 50KBytes/S, because of slow single-chip, memory less, USB1.1 speed is not fast. In addition, the code written is not good enough compression packages have circuit diagram

本文档说明AVR单片机的Atmega 16对键盘按键控制的程序-This document explains AVR MCU Atmega 16 the keyboard keys to control the procedures

6段数码管分别显示，时，分，秒，四个按键，K1（P0.0），K2（P0.1）， K3（P0.2），K4（P0.3），四个按键用来调时间的，按下K1，所有位都清零显示，然后按下K2，秒在闪烁，继续按K2分闪烁，不段地按K2 秒--分--时切换着闪烁，在某位闪时按下K3相应位加一，确认调整，按K4，取消调整再按K1。在K1按下以后才有调时的功能，如果K1没有按下，按别的键没有反映。这为了在加点按键功能留着用 -6 respectively of the digital control, when, minutes and seconds, four keys, K1 (P0.0). K2 (P0.1), K3 (P0.2), K4 (width), the four keys to the transfer time, press the K1, All spaces are reset, then press K2, the scintillation seconds, according to K2 pm flickered. not according to K2 of seconds-- minutes-- when switching to flicker in certain press the flash-K3 corresponding increase in a confirmed adjustment by K4, then canceled K1 adjustment. K1 in the press will only be made after the transfer of function, if K1 pressed by other key is not reflected. This points to the function keys used Retention