自己移植的NXP ARM IAP程序，其部分基本函数源于周立功程序，本人加了详细的注释与移植说明，还有更改编译器环境与启动代码部分说明，按照说明初次使用者便可一...

用AT89S52实现鉴相功能，用于对光电编码器的输出进行编码。-Using AT89S52 realize phase function, optical encoder used to encode the output.

* 硬件结构： PA0-5对应６个ＬＥＤ数显管的位 ，PC0-7对应各ＬＥＤ数显管的段 ，PB4-7为键盘。 * 软件描述： 上电后，时钟从00.00.00（时/分/秒）自动走时，在走时状态时 ， 按PB4（设定 * 键）超过3秒可循环选择调整时间/工作参数 ，接着按PB5以确定选择的操作 ，进入调整操作后 ， * 按PB5选择欲调整参数，按PB6（增加键）完成调整参数操作 。按PB7，进入时控运行，PB1亮， * 再按PB7停止时控运行，回显走时。在定时到时，PB0点亮。- * Hardware architecture: PA0-5 corresponds 6 LED numbers to reveal the tube the position, PC0-7 corresponds each LED number to reveal the tube the section, PB4-7 is a keyboard. * Software description: After on electricity, clock from 00.00.00 (when/a minute/second) is in luck automatically, when is in luck the condition, according to PB4 (hypothesis * The key) surpasses for 3 seconds to be possible to circulate the choice time/operational parameter, then presses PB5 by to determine the choice the operation, after enters the adjustment operation * Wants according to the PB5 choice to adjust the parameter, (increases key) according to PB6 to complete the adjustment parameter operation.According to PB7, enters when controls the mov

AVR驱动18B20例子 AVR驱动18B20例子-AVR-driven examples of AVR drive 18B20 example 18B20

该文件为研究ps/2协议在鼠标、键盘中的应用。-to study the document ps/2 agreement in the mouse, keyboard of.

Lcd 1602 module c file

基于ｆｐｇａ，采用ｑｕａｒｔｕｓ２的ＤＤＳ信号发生器，采用高速ＤＡＣ９０８为数模芯片，并可通过５１单片机送入调制信号进行ＦＭ调制-Based on the fpga, the use of the DDS signal generator quartus2 using DAC908 number of high-speed chip module, and passed into 51 single-chip FM modulation signal modulation

DSP芯片的使用,一个很有用的芯片介绍资料.-DSP chips use, a useful information on the chip.

NOKIA 5110LCD的驱动程序（带照片）MSP430的高级开发板的测试程序，主要有RS485通信，以太网通信，SD卡存储-NOKIA 5110LCD driver (with photos) MSP430 development board, senior test procedures, there are RS485 communication, Ethernet, SD card storage

关于介绍AVR单片机指令的一本书，挺不错的，在开发单片机上方便查询-AVR on the introduction of a single-chip instruction book, very good, in the development of single-chip to facilitate query

51单片机编程序学习实践经验丰富工程师编写实机通过-51 SCM-programmed study and practice of experienced engineers to prepare real machine through