8位液晶屏LCM0825的点亮源代码

通过8255查询键值，显示不同的数字。k1显示1，K2显示2，K1和K2显示3,如此类推。最多能显示7。-8,255 inquiries through the keys, show different figures. K1 shows a, K2 showed 2, K1 and K2 showed three, and so forth. The most that can be shown 7.

八段数码管显示实验（Keil），这在德国的单片机软件上可以运行。-It shows experiment (Keil digital tube), which in German single-chip microcomputer software can run.

这是一套红外解码的软件，包括硬件电路，详细使用说明！里面针对空调的国际码的界码过程有详细的描叙.-This is a set of infrared decoder software, including hardware circuit, the detailed instructions! Air-conditioning inside the International Code for the sector has a detailed code describes the process.

一些单片机C程序，希望对初学者有一定作用-Some single-chip C program, and they hope to have a role beginners

MSP430的CRC程序设计实现，位运算和查表法-MSP430 realize the CRC program design, digital computing and look-up table method

本人设计的12864完美小屏程序，供大家参考・-I design the perfect small screen 12864 procedures, for your reference

单片机控制步进驱动，S1为启动，S2为停止，S3为加一，S4为减一-Single-chip stepper drive control, S1 for the launch, S2 to stop, S3 for the plus-one, S4 for by one

仿真步骤如下： 1、把3个帖子的内容分别保存为51t9py.c,51t9py_indexa.h,5py_mb.h，放在同一目录下，将51t9py.c加入工程编译 2、由于Keil的模拟串口是单字节显示，汉字显示为乱码，所以要加挂RICHWIN或RichView这种会重新刷新显示的中文平台，或手工刷新屏幕，所以请先到 http://www.pchome.net/dl/chinese.htm 下载RichView，安装运行 3、在Keil环境下可以直接按“Ctrl＋F5”键仿真，按“F5”全速运行，切换到在串口依次输入: // 64*.6 426***.5 98*.7 936.3 586.1 4826*.1 9464*.7 64*.6试试:-) 4、按键对应(根据我自己的手机设置的,全部在PC的小键盘操作)： -simulation steps are as follows : 1 and 3 respectively, the content of messages posted on the preservation of 51t9py.c, 51t9py_indexa.h, 5py_mb.h, on the same directory, will join the project 51t9py.c compiler 2, Keil is the simulation of single-byte Serial show , the Chinese showed gibberish, so need to add or RichView RICHWIN this show will re-set the Chinese platform, or manual refresh screen, so please download RichView http://www.pchome.net/dl/chinese.htm to install three operations in Central Keil Habitat can be directly "Ctrl+ F5" key simulation, according to the "F5" running full-speed, switched to the ser

C 源码，适用于单片机的拼音输入法源程序及码表，仅包括GB2312汉字，不包括以外的-C source code, applies to SCM Pinyin input method, and source code form, only include GB2312 characters, not including outside

330PWM输出的简易程序，供C8051F330的初学者参考