Digital thermometer to take into account the use of temperature sensors, in sing...

学习C51的最好例子程序-study of the best examples of procedures

这个两个rar文件是关于定时器0使用的例子, 也是我第一次使用定时器0做的实验程序: 1. T0_ASM.rar, (带中文注释的C51语言例程), 利用定时器0中断实现LED灯的简单控制。 2. T0_C51.rar, (带中文注释的51汇编语言例程), 利用定时器0中断实现LED灯的简单控制。 两个同样功能的timer0中断程序都在MCU51-63K仿真器下通过实验, 小虾们可以试试看。 -Rar files that are both about the example of the use of Timer 0 is also the first to use my timer 0 of the experimental procedure to do: 1. T0_ASM.rar, (with English language routines C51 annotated), make use of the timer 0 interrupt implementation easy control of LED lights. 2. T0_C51.rar, (with English Notes 51 assembly language routines), use of the timer 0 interrupt achieve easy control of LED lights. Same function in both programs at timer0 interrupted MCU51-63K emulator through the experiment, shrimp can give it a try.

飞思卡尔HC08/HCS08系列单片机LCD驱动源码，希望对大家有用。-Freescale HC08/HCS08 series of single-chip LCD driver source code, in the hope that useful to everyone.

我用单片机8952和电压比较器339做了一个简单的电容容量测量表，参数大 致如下： 电容测量范围为1pF-9999.99uF，最小分辨力为1pF。分为5个量程，可以自 动切换量程，也可手动切换。 另外，有简单的频率计功能，能测量0-60MHz的数字信号频率（TTL电平）； 还可以产生几个单点频率的方波信号（比如1KHz）。 采用1602LCD作为显示器；4个按键控制；使用24C01保存当前设置值，不用 每次开机重新设置。可单5V供电，也可9V交流供电 -I used the single-chip 8952 and the voltage comparator 339 to do a simple capacitance measurement table, parameters are as follows: capacitance measurement range 1pF-9999.99uF, the minimum resolution for the 1pF. Divided into five ranges, you can automatically switch range can also be manually switched. In addition, a simple frequency meter function, capable of measuring 0-60MHz frequency digital signal (TTL level) can also lead to several single-point-frequency square-wave signal (for example, 1KHz). 1602LCD used as a monitor 4 button control use 24C01 to preserve the current settings, do not reset each boot. Can be a single 5V power supply, 9V AC power supply can also be

crc快速校验程序,对于新手很快就能看懂的,结合实际读一读友好处!-Fast CRC checksum procedure, for the novice to understand quickly, and in light of the actual read friendly Office!

7279(完全功能) 32位键盘 8位LED显示驱动程序-7279 (full function) 32 keyboard 8 LED Display Drivers

使用1520控制器的12232点阵液晶模块的51单片机控制C代码,keil编译通过,使用端口直接连接方法,P1口为数据口,控制线在P3部分端口-1520 controller using dot matrix LCD module 12232 51 C MCU control code keil compiled by the use of ports directly connected, I P1 for data export, the line of control in some ports P3

74HC595程序,C51版的,己调试过-74HC595 procedures, C51 version, others have been debug

基于DS1302的数码管时钟电路设计源程序,使用C51语言编写，可以用于MCS8051单片机-based on the DS1302 digital clock control circuit design source, the use of C51 language, which can be used Mcs8051 MCU

这篇程序是我一个同学编的,并且已经应用到了二相步进电机(四线步进电机)上了.但是我认为此程序需要改进的地方有很多. -This procedure is a fellow student, I made and have been applied to a two-phase stepper motor (four-wire stepper motor) on. But I think this process needs to be improved where there are many.