登录
首页 » Matlab » ID3决策树分类算法代码

ID3决策树分类算法代码

于 2022-02-13 发布 文件大小:3.84 kB
0 98
下载积分: 2 下载次数: 1

代码说明:

主要为数据分析和统计,大学数值分析算法,包括压缩比、运行时间和计算复原图像的峰值信噪比,是机器学习的例程,数据模型归一化,模态振动,采用了小波去噪的思想。

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • Icbirzipm
    用于进行图像类别识别的程序。根据初步的的区域分割结果,对图像之间的区域进行匹配。 (For image category recognition program. According to the initial region segmentation results, the region between the two images match.)
    2012-05-21 22:41:00下载
    积分:1
  • vfim
    A three phase induction motor drive using a V/F control
    2012-07-22 21:55:48下载
    积分:1
  • cuckooMain
    Therefore, the Z-source inverter can buck and boost voltage to a desired output voltage that is greater than the available dc bus voltage
    2015-01-18 23:46:55下载
    积分:1
  • gjsetrzn
    解耦,恢复原信号,有小波分析的盲信号处理,包含了阵列信号处理的常见算法,仿真图是速度、距离、幅度三维图像,利用自然梯度算法,最小均方误差(MMSE)的算法,多抽样率信号处理。(Decoupling, restore the original signal, There Wavelet Analysis Blind Signal Processing, Contains a common array signal processing algorithm, FIG simulation speed, distance, amplitude three-dimensional image, Use of natural gradient algorithm, Minimum mean square error (MMSE) algorithm, Multirate signal processing.)
    2016-03-27 11:25:08下载
    积分:1
  • 可见光通信最大化最小速率_matlab
    说明:  计算可见光通信中最大化最小速率的优化问题,还有稳健波束成形(The optimization problem of maximizing the minimum rate and robust beamforming are also discussed)
    2020-08-11 20:08:27下载
    积分:1
  • commands-for-data-fitting
    本文详尽阐述了如何在matlab编程环境下对数据拟合和插值的各种命令(This article elaborates how matlab programming environment for data fitting and interpolation of the various commands)
    2011-01-23 10:20:57下载
    积分:1
  • sparse_grid_cc_se_size
    Clenshaw Curtis Slow Exponential Growth.
    2012-03-30 08:32:10下载
    积分:1
  • AHP
    说明:  根据输入的决策矩阵,利用AHP方法,进行0-1标准化处理,得出标准化后的结果。(According to the input decision matrix, the AHP method is used to perform 0-1 normalization processing, and the standardized result is obtained.)
    2020-06-17 11:00:02下载
    积分:1
  • 要求:从x(t)=sin(2*pi*5*t)+sin(2*pi*200*t)+sin(2*pi*50*t)信号中滤出频率为5Hz的信号...
    要求:从x(t)=sin(2*pi*5*t)+sin(2*pi*200*t)+sin(2*pi*50*t)信号中滤出频率为5Hz的信号-Requirements: from x (t) = sin (2* pi* 5* t)+ sin (2* pi* 200* t)+ sin (2* pi* 50* t) signal to filter out the signal frequency of 5Hz
    2022-02-06 02:34:00下载
    积分:1
  • juzhenlun
    基于matlab的矩阵论算法,有利于矩阵论初学者使用(Algorithm based on matlab of matrix theory, matrix theory in favor of beginners)
    2015-11-03 20:24:06下载
    积分:1
  • 696516资源总数
  • 106914会员总数
  • 0今日下载