VB to do with the serial debugging assistants, can be used to lower PC and the c...

LCD driver HX8802_datasheet

基于测距式的超声波测距仪，以AT89C51单片机为核心，精度高、有数字显示功能，实验精度达0.5CM-location-based ultrasonic range finder to AT89C51 core, high precision, digital display, experimental accuracy of up to mile

nRF905无线FSK芯片在51单片机上工作的代码-nRF905 FSK wireless chip microcontroller in 51 working on the code

在FLASH中写入一个字节,用数据轮询的方式检测写入状态-FLASH writes in a byte, using the data polling way to write state detection

我自己在别人基础上编写的MSP430F410的例程，希望能对大家有帮助-myself in other people prepared on the basis of MSP430F410 routines, we hope to help

C51单片机数码管显示通用接口显示模块源码奉献-C51 microcontroller Universal Display Digital Interface Module dedicated source

基于中断控制的声光报警器的设计.采用中断方式，设计一个声光报警器的硬件电路和控制程序。程序运行时，一旦8位开关信号量状态满足设定条件，就触发中断，使发光二级管按规律闪烁，同时扬声器播放一段音乐。 硬件设备包括一台微机、一个MFID微机实验箱、一块T型板，2输入四与门 74ls08、8位总线驱动器 74ls245、LM386A音频放大器、排阻、扬声器各一个，发光二极管8个，470uF电容2个、104电容4个，插线若干。 -Interrupt-based control of sound and light alarm design. Using interrupt mode, designing a sound and light alarm hardware circuits and control procedures. The program is running, once the 8-bit switch signal to set the amount of state to meet the conditions to trigger interrupts, so that light-emitting diode flashes according to the law, while speakers play a piece of music. Hardware includes a computer, a computer simulation, MFID box, a T plate, 2 input 4 and gate 74ls08, 8-bit bus driver 74ls245, LM386A audio amplifier, exclusion, speakers of a light-emitting diode 8, 470uF capacitor 2 a, 104 capacitors 4, plug-line number.

IC卡操作软件:AT88SCl604芯片的操作模式有五种。它们是通过配PGM、RST、CLK等引脚信号及内部地址计数器(IAC)的状态组合来实现。 (1) 芯片复位操作： AT88SCl604有两种复位方式:上电复位和控制复位。 上电复位： 上电复位是当芯片加电时的最初状态。上电复位属于芯片 内部复位。它将使芯片内部所有的隐含标志复位到"0"状态。并使地址计数器复位到0位。 控制复位： 当CLK为低时，在RST脚上的一个下降沿将便芯片产生复位操作。 控制复位是将地址计数器复位到0位，而不影响任何内部标志的状态。-IC Card operating software : AT88SCl604 chip mode of operation there are five. They are allocated by PGM, RST, etc. pin CLK signal and the internal address counter (IAC) portfolio of the state is to be achieved. (1) chip reset operation : reduction AT88SCl604 two ways : power-on reset and reset control. Power-on reset : power-on reset when the chip is in power at the initial state. Power-on reset the internal chip is reset. It will enable all internal chip implied signs reset to "0" state. Make address counter reset to 0. Reset control : When the CLK for the low, the RST feet of a falling edge chips will have to reset operation. Reset control is to address counter reset to 0, without prejudice to any signs of internal sta

The example uses the GPIFTool utility to illustrate single/burst data read(s)/write(s).

基于FREESCALE单片机9S08DZ60的LIN从节点的应用层源代码.LIN是通过UART串口来实现的.开发环境为CODEWARRIOR FOR HC08-Based on Freescale