通过设置发送并接收消息：可以设置端口，波特率，奇偶校验等参数...

RS编码 CodeWarrior环境例程！-RS CW environmental routines!

在LPC2106实现的中断函数和demo,本例程仅对初学这有用-Implemented in LPC2106 interrupt function and the demo, this routine is only useful for beginners This

ATmega128串口通信,在ICC AVR下编译成功-ATmega128 uart communication

一个中断法串口通讯程序。-A serial communication programme written by os interruption

这个文件夹里共3个部分，分别是串口编程与ODBC技术结合，用API函数控制串口和用MSComm控件控制串口。-This folder in a total of three parts, which are serial programming and ODBC technology, using API functions to control serial port and serial port control by MSComm control.

VC实现串口通信例程 VC实现串口通信例程 VC实现串口通信例程 -VC serial communication routines VC serial communication routines VC serial communication routines VC serial communication routines VC serial communication routines VC Serial Communication routines

本程序是i2c总线读写一个字节的程序。在写过程序中，不一定非要检测i2c的应答位，可以直接延时过去就行，但是在读过程中必须给应答信号，读完发停止位，一定确认所发的信号都发上了。否则在连续地址读的过程中可能不会出错，但是在随机度过程中就会出错，我的程序就是在给停止信号时没有给上，24cxx一直在输出数据，结果读出错。找着问题后我的程序只加入了一条命令便完全正常。-i2c bus read and write a byte procedures. The written procedure, not necessarily require the detection i2c-response, and can directly past trip delay, but the process must be read to the response signal, stopped at reading, we recognize the signals are on the fat. Otherwise, the address read for the course could not go wrong, but the randomness of the process would be a mistake, I was in the process to stop for no signal, 24cxx in output data, read errors. I discovered the problem after the procedure just joined the order of a completely normal.

串口数据转换,VB60源程序,本人从网上收集，分享给大家，谢谢，没有解压密码.-Serial data conversion, VB60 source, I gather from the Internet, to share to you, thank you, there is no decompression password.

云台根据其回转的特点可分为只能左右旋转的水平旋转云台和既能左右旋转又能上下旋转的全方位云台。一般来说，水平旋转角度为0°～350°，垂直旋转角度为+90°。恒速云台的水平旋转速度一般在3°～10°/s，垂直速度为4°/s左右。变速云台的水平旋转速度一般在0°～32°/s，垂直旋转速度在0°～16°/s左右。在一些高速摄像系统中，云台的水平旋转速度高达480°/s以上，垂直旋转速度在120°/s以上 -Yuntai rotation in accordance with its characteristics can be divided into only about the level of rotation and can rotate around Haeundae rotating up and down while rotating omni-directional PTZ. In general, the level of rotation angle 0 ° ~ 350 °, vertical rotation angle for+ 90 °. The level of constant rotation speed Yuntai generally 3 ° ~ 10 °/s, the vertical speed of 4 °/s or so. The level of variable rotation speed Yuntai generally 0 ° ~ 32 °/s, vertical rotation speed 0 ° ~ 16 °/s or so. In some high-speed camera system, the level of Yuntai rotating at speeds of up to 480 °/s or more, vertical rotation speed 120 °/s over

的问题.派尔高协议,控制左转右转时,出现问题.其他功能好用.我用DELPHI写的程序,在MOUSEDOWN中, str := chr($FF)+chr($01)+chr($00)+chr($04)+chr($0F)+chr($00)+chr($14) MSComm1.output := str 在CLICK事件中: str := chr($FF)+chr($01)+chr($00)+chr($00)+chr($00)+chr($00)+chr($01) MSComm1.output := str -Problem. Pelco agreement左转右转control when there are problems. Other features easy to use. DELPHI I used to write the procedures in the MouseDown, str: = chr ($ FF)+ Chr ($ 01)+ chr ($ 00)+ chr ($ 04)+ chr ($ 0F)+ chr ($ 00)+ chr ($ 14) MSComm1.output: = str in the CLICK event: str: = chr ($ FF)+ chr ($ 01)+ chr ($ 00)+ chr ($ 00)+ chr ($ 00)+ chr ($ 00)+ chr ($ 01) MSComm1.output: = str