使用Delphi编写的串口通信控制器，具备文件传输功能

The PCD5003A is a very low power decoder and pager controller specifically designed for use in new generation radio pagers. The architecture of the PCD5003A allows for flexible application in a wide variety of radio pager designs. The PCD5003A is fully compatible with “CCIR Radio paging Code No. 1” (also known as the POCSAG code) operating at data rates of 512, 1200 and 2400 bits/s using a single oscillator crystal of 76.8 kHz. In addition to the standard POCSAG sync word the PCD5003A is also capable of recognizing up to 4 User Programmable Sync Words (UPSWs). This permits the reception of both private services and POCSAG transmissions via the same radio channel. Used together with the Philips UAA2080 or UAA2082 paging receiver, the PCD5003A offers a highly sophisticated, miniature solution for the radio paging market. Control of an RF synthesizer circuit is also provided to ease alignment and channel selection

MSComm控件资料,Visual Basic 6.0(以下简称VB) 是一种功能强大、简单易学的程序设计语言。它不但保留了原先Basic语言的全部功能，而且还增加了面向对象程序设计功能。它不仅可以方便快捷地编制适用于数据处理、多媒体等方面的程序，而且利用ActiveX控件MSComm还能十分方便地开发出使用计算机串口的计算机通信程序。本文结合计算机通信的两个例子，详细介绍如何在VB中使用MSComm控件。 处理方式 -MSComm information, Visual Basic 6.0 (VB hereinafter) is a powerful, relatively simple programming language. It not only retains the original Basic language functionality, but also an increase of object-oriented programming design functions. It will not only facilitate the efficient preparation of the application to data processing, multimedia and other aspects of the procedure, and the use of MSComm ActiveX control can be very convenient to use the computer to develop the computer serial port Communication Program. Based on computer communication, the two examples in detail how to use VB MSComm. Approach

串口通信程序，完成数据采集，验证证明正确，可以使用哦-Serial communication program, the completion of data acquisition, validation to prove correct, you can use the oh

485通讯接口模块的编程应用，监控显示，检测报警显示，上下值的设置输入输出的结构-485 Communications Interface Module programming applications, monitor display, alarm detection showed that the whole value of the structure of input and output settings

串口调试测试文件-Serial debug test file

本程序是i2c总线读写一个字节的程序。在写过程序中，不一定非要检测i2c的应答位，可以直接延时过去就行，但是在读过程中必须给应答信号，读完发停止位，一定确认所发的信号都发上了。否则在连续地址读的过程中可能不会出错，但是在随机度过程中就会出错，我的程序就是在给停止信号时没有给上，24cxx一直在输出数据，结果读出错。找着问题后我的程序只加入了一条命令便完全正常。-i2c bus read and write a byte procedures. The written procedure, not necessarily require the detection i2c-response, and can directly past trip delay, but the process must be read to the response signal, stopped at reading, we recognize the signals are on the fat. Otherwise, the address read for the course could not go wrong, but the randomness of the process would be a mistake, I was in the process to stop for no signal, 24cxx in output data, read errors. I discovered the problem after the procedure just joined the order of a completely normal.

串口编程（中文翻译版）----绝对经典书籍

楼宇自控系统 希望对各位有用-Building Automation System hope useful to you!

win2000下的与下位机UART的串口通信程序-WIN2000 with the crew under the UART serial communication program

华邦单片机W77E58的中文芯片资料,给广大英语薄弱的程序开发和爱好者跟好地掌握W77E58使用带来了方便.-Winbond Singlechip W77E58 Chinese chip information to the general procedure for the development of English is weak and enthusiasts with a good grasp W77E58 brings convenience to use.