LCM module .9320 relevant information .320 X240

本源程序使用C51控制的PLL(SANYO LC72131)收音,可以通过HT1621驱动LCD显示,有完整的按键控制程序模块,能通过KEY进行各种功能操作,整个程序采用模块化设计,移植方便,可以初学者参考使用.(之前的那个也是我上载的,怎么就没开通?)-C51 use the source control PLL (SANYO LC72131) radio, Driving through HT1621 LCD Display, a complete module button control procedures, KEY through various functional operation, the whole process has a modular design and facilitate transplantation, beginners can use and reference. (which is also before I posted, how never opened)

AT45DB041B读写C51源码,带芯片资料-AT45DB041B read and write source code C51, with the chip data

　C8051F330/1 MCU 有一个可编程内部高频振荡器、一个可编程内部低频振荡器和一个外部振荡器驱动电路。可以通过对 OSCICN 和 OSCICL 寄存器编程来使能/禁止内部高频振荡器和调节其输出频率（参看振荡器框图）；可以通过对 OSCLCN 寄存器编程来使能/禁止内部低频振荡器和调节其输出频率（参看图9.3）。系统时钟可以由外部振荡器电路或任何一个内部振荡器提供。表9.1给出了内部振荡器的电气特性。 -C8051F330/1 MCU has a programmable internal high-frequency oscillator, a programmable internal low frequency oscillator and an external oscillator drive circuit. Can register on OSCICN and OSCICL programming to enable/disable the internal high-frequency oscillator and adjust its output frequency (see diagram oscillator) OSCLCN can register through the programming to enable/disable the internal low frequency oscillator and adjust its output frequency (see Figure 9.3). System clock can be external oscillator circuit, or any provision of an internal oscillator. Table 9.1 gives the electrical characteristics of the internal oscillator.

这是一本”平凡单片机试验板制作资料.rar“教大家怎么制作单片机的试验的，不错-This is an "extraordinary board microcontroller pilot production of information. Rar "to tell you how the pilot production of the single-chip microcomputer, yes

对电网参数的测量程序，可测量多个参数，包括LED显示和键盘中断程序-network parameters on the measurement procedures, a number of measurable parameters, including LED display and keyboard interrupt procedures

C51中的指针应用之一.rar-C51 target of one application. Rar

单片机显示子程序初始化 C语言编程 保证好用-Single-chip display initialization subroutine to ensure that use C language programming

这是一个简单的红外解码程序，是针对9ms起始码和4.5ms结束码的红外信号。晶振用的是11.0592M的，经测试能用。-This is a simple infrared decoding procedure is 9ms start code and end code 4.5ms infrared signal. 11.0592M crystal is used, and can be tested.

CAN三台机子互相通讯（机子3程序），已调通，标准的标识符，11位。-CAN communication with each other three loom (loom 3 procedures), Qualcomm has been transferred, the standard identifier, 11.

控制电机运动的G代码程序,如果对G代码不清楚,请先看懂G代码,然后再看本程序.-Control motor movement, G code program, if the G code is not clear, please understand G code, and then look at the procedures.