一个使用c51单片机制作的电源管理程序 包括TLC2543,DS12887,24c64等程序！程序完整！...

针对MSP430的金鹏OCMJ4X8C128×64中文液晶驱动程序,只支持串口模式，已调试可用-For the MSP430-Jinpeng OCMJ4X8C128 × 64 Chinese LCD driver supports only serial mode, has been used to debug

单片机中的EEPROM模块，在CVAVR中已实现。-Single-chip EEPROM in the module, in CVAVR already realize.

smart2300平台全部驱动例程 LPC2378所有中间件，非常有用，可以移植到各操作系统-LPC2378 ADC I2C RTC UART SSP IrDA CAN I2S LCM SD USB

与单片机接通,实时获得室内温度和湿度数据的程序.-Connected with the single-chip, real-time access to the indoor temperature and humidity data.

我用单片机8952和电压比较器339做了一个简单的电容容量测量表，参数大 致如下： 电容测量范围为1pF-9999.99uF，最小分辨力为1pF。分为5个量程，可以自 动切换量程，也可手动切换。 另外，有简单的频率计功能，能测量0-60MHz的数字信号频率（TTL电平）； 还可以产生几个单点频率的方波信号（比如1KHz）。 采用1602LCD作为显示器；4个按键控制；使用24C01保存当前设置值，不用 每次开机重新设置。可单5V供电，也可9V交流供电 -I used the single-chip 8952 and the voltage comparator 339 to do a simple capacitance measurement table, parameters are as follows: capacitance measurement range 1pF-9999.99uF, the minimum resolution for the 1pF. Divided into five ranges, you can automatically switch range can also be manually switched. In addition, a simple frequency meter function, capable of measuring 0-60MHz frequency digital signal (TTL level) can also lead to several single-point-frequency square-wave signal (for example, 1KHz). 1602LCD used as a monitor 4 button control use 24C01 to preserve the current settings, do not reset each boot. Can be a single 5V power supply, 9V AC power supply can also be

18b20与单片机，与电脑之间串口通信，可以扩展温度计-18b20 and MCU with serial communication between computers, you can extend the thermometer

C8051F系列单片机SPI端口驱动程序，简洁，高效。-C8051F MCU SPI port drivers, simple and efficient.

CAN总线调试通过的程序，SJA1000芯片的Peli CAN模式下的C51源程序-CAN bus debug the procedure adopted, SJA1000 chip Peli CAN mode source of C51

This directory contains 3 file system modules: - file system ISO9660 iso9660.c iso9660.h - file system FAT12/16 fat.c fat.h - file system FAT32 fat32.c fat32.h file.c and file.h contains all high levels functions/macro/definition for your application. fs_variable.c contains all definitions of variables that can be shared with the all file systems. config.h must contain the definition of the file system used by your application.- This directory contains 3 file system modules:- file system ISO9660 iso9660.c iso9660.h- file system FAT12/16 fat.c fat.h- file system FAT32 fat32.c fat32.h file.c and file.h contains all high levels functions/macro/definition for your application. fs_variable.c contains all definitions of variables that can be shared with the all file systems. config.h must contain the definition of the file system used by your application.

EBU格式加GPS0183对时完整实现程序源代码，值得收藏和直接应用，是本人实际的程序！-EBU format at the right increase GPS0183 achieving complete source code, it is worth collecting and direct application I is the actual procedure.