ad转换0809的引用实例，次程序调试过，用作数字电压表，精度还不错。...

///*** *** *** * //一、程序说明： //1, 24LC02器件地址是1010000R/W. //2, 数组写入24LC02采取页写方式. //3, 数组code从24LC02读出时采取自由读方式. //4, 采用4.00M晶体。 //5，采用软件I2C。 //二、硬件连接： //1， SDA------->23 pin.(当然你可以任意选择脚位） //2, SCL------->18 Pin.(当然你可以任意选择脚位） //3， PORTB----->数码管的段输出 //4， RD4，RD5，RC6，RC7------->数码管的位输出(数码管为共阴极） -///*******************// A description of the procedures:// 1, 24LC02 device address is 1010000R/W.// 2, write an array to take 24LC02 page write mode.// 3, the array read out the code from the 24LC02 to take a free read.// 4, using 4.00M crystal.// 5, using software I2C.// Second, the hardware to connect:// 1, SDA-------> 23 pin. (Of course, you can choose to pin)// 2, SCL-------> 18 Pin. (Of course You can choose pin)// 3, PORTB-----> digital tube output segment// 4, RD4, RD5, RC6, RC7-------> digital pipe-bit output (digital tube for a total of cathode)

红外线遥控器按键检测程序. 通过检测两次下降沿之间的时间差判断接受到的数据位. 已经通过了测试,能够正确区分出32bit数据的遥控器按键键值. 具有数据重发功能,但是数据的重发有点频繁. 使用晶震频率为11.0592MHz,所有定时值都是基于这个频率计算. 占用很少量的CPU时间,使用了外部中断0接受数据,定时器0进行计数, 定时器1作为串口的波特率发生器(Band = 9600).-Infra-red remote control button detection program. By detecting falling edge twice to determine the time difference between the received data bit. Has passed the test, could correctly distinguish 32bit data button remote control key. With data re-issued, but data a bit of re-issued frequent. Zhenyuan frequency of use of crystal 11.0592MHz, all timing values are calculated based on this frequency. occupied by small quantities of CPU time, use the external interrupt 0 to accept data, timer 0 to count, timer 1 as a string port baud rate generator (Band = 9600).

SDU的字库，主要包垮一些程序代码，很好用的，希望对大家有用-SDU

自己用汇编编写的键盘的扫描程序 希望和大家共享!-his own compilation prepared by the keyboard scan and you will share!

云台是一种设备,可以说是专门用于监控时调整摄像头位置所用.-Haeundae is a kind of equipment, can be said to be dedicated to monitoring, adjust the camera position used.

针对51核的实验程序，包括汇编语言核C语言，有交通灯，步进电机，滤波器等-against nuclear Experimental procedures, including nuclear assembly language C language, and traffic lights, stepper motors, filters, etc.

也用到了温度PID控制,和我门的不同是采用D/A输出控制量的.主要由温度采样--->温度滤波子程序--->温度线性化----->温度设定值等模块组成.-also uses a PID temperature control, and my door is different D/A output volume control. By sampling temperature--- gt; Temperature filter subroutine-- gt; Temperature linear----- gt; The temperature setpoint and other modules .

1302时钟芯片的pic程序，完全可以应用在其他的单片机上（不过好像如果速度太快的要改一下）-1302 clock chip pic procedures can be applied to other MCU (But if the pace seems too fast to change it)

出租车计费显示，采用凌阳61单片机加液晶显示器实现的。具有产品价值-Taxi billing shows that the use of Sunplus 61 single-chip LCD plus achievable. With product value

LM35 thermometer sensor. High linearity, high resolution.