在PROTEUS仿真实现，在液晶显示器上显示采集温度的波形图

红外通信是利用950nm近红外波段的红外线作为传递信息的媒体，即通信信道。发送端采用脉时调制（PPM）方式，将二进制数字信号调制成某一频率的脉冲序列，并驱动红外发射管以光脉冲的形式发送出去；接收端将接收到的光脉转换成电信号，再经过放大、滤波等处理后送给解调电路进行解调，还原为二进制数字信号后输出。-Infrared communication is the use of near infrared 950nm infra-red as the transmission of information media, namely communication channel. The sending end when the use of pulse modulation (PPM) approach will be a binary digital signal into a frequency modulation of the pulse sequence, and driver fired infrared tube to the form of light pulses sent receiver will receive the pulse of light conversion to electrical signals , and then, after amplification, filtering and other treatment to the demodulation circuit after demodulation, reduced to a binary digital signal after the output.

控制电机运动的G代码程序,如果对G代码不清楚,请先看懂G代码,然后再看本程序.-Control motor movement, G code program, if the G code is not clear, please understand G code, and then look at the procedures.

基于Ramtron公司的VRS51L3074高性能8位单片机的MP3(VS1003)驱动程序,程序在Keil环境编译,程序内自带一段15K左右的MP3文件,可以直接播放测试.-Based on Ramtron" s VRS51L3074 high-performance 8-bit microcontroller MP3 (VS1003) drivers, programs, the environment in the Keil compiler, the program comes with a 15K or so inside the MP3 files can play test.

STC系列51单片机串口下载软件,是学习51单片机的必备工具.通过这个软件,可以把已经编译好的程序接上下载器,下载到单片机上,就可以实现程序的下载,对硬件方面的学习是至关重要的!-STC Series 51 Single-chip serial download software is an essential learning tool for single-chip microcomputer 51. Through this software, you can already compiled program to access the download, and downloaded to a single-chip, you can download the realization of the procedure on the hardware side of learning is essential!

F_Dtecter 单片机频率计 精确度1％以上 -Singlechip F_Dtecter Cymometer more than 1 accuracy

摘要：提出了一种基于单片机与AD9852的信号源的实现，重点介绍了单片机与AD9852硬件接口电路、AD9852串行工作流程以及宽带滤波器设计的关键技术。 关键词：AD9852；信号发生器；频率合成

16*16点阵源C程序，keil开发,可以显示32个字,从左到右滚动显示。-16*16

OCM12864的基本使用方法和实现多菜单的实现。-OCM12864 the basic use of methods and the realization of multi-menu.

是MSP430与HD44780显示的程序，由C语言编写-HD44780 is the MSP430 with the show processes from C language

功能：实现对DS18B20的读取 原理：单总线协议 注意：单总线协议对延时要求比较严格，此程序中采用的是11.0592M的晶振，如果使用其他的晶振请跟据DS18B20的资料修改延时参数-functions : to achieve DS18B20 read Principle : single-bus protocol attention : single-bus protocol to delay requirements more stringent, this procedure is used in the crystal 11.0592M if the use of other crystal please According to the information DS18B20 delay parameter changes