AT91SAM7S256开发板基础demo，已验证

AVR单片机入门及C语言高效设计实践（五） ATMEAG16L的中断系统什么是“中断”？顾名思义中断就是中断某一工作过程去处理一些与本工作过程无关或间接相关或临时发生的事件，处理完后，则继续原工作过程。比如：你在看书，电话响了，你在书上做个记号后去接电话，接完后在原记号处继续往下看书。如有多个中断发生，依优先法则，中断还具有嵌套特性。又比如：看书时，电话响了，你在书上做个记号后去接电话，你拿起电话和对方通话，这时门铃响了，你让打电话的对方稍等一下，你去开门，并在门旁与来访者交谈，谈话结束，关好门，回到电话机旁，拿起电话，继续通话，通话完毕，挂上电话，从作记号的地方继续往下看书。由于一个人不可能同时完成多项任务，因此只好采用中断方法，一件一件地做。[第一段] -AVR C language portal and efficient design practice (5) ATMEAG16L the system even interrupted Mody is "suspended"? As the name suggests is interrupted interruption of a process to deal with some of the work process unrelated or indirectly related to the temporary or , after treatment, to the original process. For example : in your reading, the phone rang, you have the book to be a mark after picking up the telephone, then after the original mark to continue down the reading. For more interruption, priority rules and the suspension characteristics also have nested. For instance : reading, the phone rang, you have the book to be a mark after pick

圣诞礼物！满有意思的！为大家奉献-Christmas gifts! Full of fun! Dedication for everyone. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

通过小磁片对霍尔传感器所产生的电平变化进行记数的C程序~-Hall sensors through the small disk on the level generated by changes in procedures for counting of C ~

aduc814的汇编程序例子-ADUC814 example of the compilation process

YM12864R___相关网上下的资料 ,里面有程序和LCD的详细资料及相关字模的软件.足够写个驱动了.-YM12864R___ under the relevant information online, There are procedures and the detailed information on the LCD and related Fonts software. enough to write a driver of.

SST系列单片机的中文资料。包括用SST89系列单片机和SoftICE做软件的在线仿真,使用EasyIAP在线下载的说明,使用EasyIAP在线下载的说明,SST单片机IAP指令操作程序示例汇编语言,SST单片机IAP指令操作程序示例C语言，SST89x554-564资料,sst89x5x4Rx头文件等等，打包下载-SST Series Singlechip Chinese information. Including SST89 Series MCU and SoftICE software to do online simulation, the use of online download EasyIAP note, the use of online download EasyIAP note, SST Singlechip IAP operating procedures sample assembly language instructions, SST Singlechip IAP commands operating procedures sample C language, SST89x554-564 information, sst89x5x4Rx header files, etc., packaged download

8051的UDP协议实现 协议实现--c语言编写 用51单片机实现的。-8051 to achieve the UDP protocol-- c language with the MCS-51 microcontroller.

关于SPLC501C的液晶编程，实现了音乐动画，有参考价值-on SPLC501C LCD programming, animation realization of the music, a reference value

三相步进电机的三相六拍工作方式，正转的绕组通电顺序：A、AB、B、BC、C、CA、A，反转的通电顺序：A、AC、C、CB、B、BA、B、A。 由于步进电机转子有一定的惯性以及所带负载的惯性，故步进电机的工作过程中不能及时的启动和停止，在启动时应慢慢的加速到预定速度，在停止前应逐渐减速到停止，否则，将产生失步现象。 步进电机的控制问题可总结为两点： 1、产生工作方式需要的时序脉冲； 2、控制步进电机的速度，使它始终遵循加速、匀速、减速的规律工作。 -Three-phase three-phase stepper motor six shot work, is to order the winding power: A, AB, B, BC, C, CA, A, reverse the order of power: A, AC, C, CB, B, BA, B, A. As the stepper motor rotor has a certain degree of inertia, as well as brought about by the inertia load, the stepper motor during the course of work should not start and stop time, start to be slowly accelerated to a predetermined speed, the stop should be to slow down gradually to the stop, otherwise, will result in out-of-step phenomenon. Stepper motor control problems can be summarized in two points: one, resulting in the need to work the timing pulse 2, control the speed of stepper motor, so that it always followed acceleration, velocity, deceleration of the law of the work.

凌阳IED2.0.0，全国大学生电子设计竞赛数控直流源的凌阳代码-Sunplus IED2.0.0, National Undergraduate Electronic Design Contest NC Sunplus DC source code