利用多模式调制解调器芯片CMX868能直接通过高速串行总线与单片机串行接口进行通信这一特点设计的一套采用单片机来控制CMX868芯片的数据传输系统，握手协议部分...

简易空调控制程序 KEIL+PROTUNES-Simple air-conditioning control procedures KEIL+ PROTUNES

基于单片机的8路抢答器 原理图 源码全部都有-Based on single-chip 8 Rd Answer schematic source browser, all of the above

本代马是以AVR系列单片机为硬件，开发环境采用ICCAVR，用软件模拟I2C总线-this generation is MCUs for hardware, using ICCAVR development environment with software simulation I2C Bus

单片机控制RTL8019网卡芯片实现TCP/IP协议栈是一件非常有意思的实验。我尝试使用专门针对8位单片机设计的uIP6.0在mcu51-63K仿真器移植成功-SCM control RTL8019 chip Ethernet TCP/IP protocol stack is a very interesting experiment. I try to use specific 8-bit microcontroller design uIP6.0 in mcu51- 63K simulator transplant success

void InitGoertzel(void) 作用：初始化算法参数 用法：采用算法进行检测前执行一次，如果需要改变参数，调用SetParameter() float CGoertzel::GetMagnitude(unsigned char * sampleData, int length) //算法主接口 作用：对采集下来的音频数据用算法处理，返回一个结果 参数：sampleData－音频数据缓冲地址指针； length-缓冲区尺寸(音频数据数量),字节数； 返回值：返回算法结果。 void SetParameter(DWORD set_SampleRate, DWORD set_TargetFreq, DWORD set_BlockSize) 作用：设置算法参数； 参数：set_SampleRate-音频数据抽样速率； set_TargetFreq-目标信号频率； set_BlockSize－算法数据块尺寸(采样点)； 用法：调用本函数后，需要调用一次InitGoertzel(void)才会生效-void InitGoertzel (void) function: initialization algorithm parameters Usage: The algorithm performs a pre-test, if the need to change the parameters, calling SetParameter () float CGoertzel:: GetMagnitude (unsigned char* sampleData, int length)// Algorithm for the main interface role: to collect audio data from the treatment algorithm to return a result parameter: sampleData-audio data buffer address pointer length-buffer size (the number of audio data), number of bytes return value: the return of

PC - MCU 串行通迅程序 单片机接收主机的数据,然后将数据传送到P0口, 并传回给主机 当按下AN1时, 单片机发送字串给主机-PC-MCU serial communications procedures SCM receive mainframe data, and data transmission to the P0 mouth and passed back to the mainframe when pressed AN1, SCM string sent to the mainframe

该模拟器是在Keil7.0中使用。 只要把Ex02Dll.dll复制到 X:KeilC51BIN目录下。 打开测试程序，编译运行即可看到如图led.jpg中所显示的效果。-The simulator is used in Keil7.0. As long as Ex02Dll.dll copied to the X : Keil C51 BIN directory. Open test procedure, compile operation can be seen in figure led.jpg reflected by the results.

日本产五相步进电机的正转及反转动作控制。-Japan five-phase stepper motor is to control and reverse action.

此程序为单片机开发过程中定时芯片ds1302的控制并用lcd显示的程序，用汇编语言编写。供参考用-procedure for microcontroller development process of regular chips ds1302 control and LCD display with the procedures in assembler language. For information

ATMEL 89sxx 系列51单片机下载线原理图 这是ATMEL公司的官方板-ATMEL 89sxx Series 51 Single-chip line schematic download This is the official board ATMEL Corporation