This is the source C8051F020, well, this single chip a powerful, easy to learn p...

用keil c编写的PID算法,不错噢.-with keil c prepared by the PID algorithm, Oh Yes. Ha ha

用WAVE6000开发环境写的电子钟程序-WAVE6000 development environment used to write procedures for electronic bell

本程序用于MICROCHIP 24LC64 EEPROM的读写。本程序不使用芯片级联方式， 请将A0，A1，A2 管脚接至低电平。本程序使用IOC6作为SDA，IOC7作为SCL。 程序中的地址空间最大可至64K：24LC00-16-0，24LC01-128-8，24LC02-256-8， 24LC04-512-16，24LC08-1K-16，24LC16-2K-32，24LC32-4K-32，24LC64-8K-32， 24LC128-16K-64，24LC256-32K-64，24LC512-64K-128，读写数据均为8bits。 以上器件的格式为（型号-地址空间-页大小）不同器件的页大小不同，因此页写 程序需作相应修改，其他字节写，随机读以及顺序读程序均相同-This procedure for the MICROCHIP 24LC64 EEPROM read and write. This procedure does not use chips cascade way, please A0, A1, A2 pin to low level access. This procedure used IOC6 as SDA, IOC7 as SCL. Process address space available to the largest 64K: 24LC00-16-0, 24LC01-128-8, 24LC02-256-8, 24LC04-512-16, 24LC08-1K-16, 24LC16-2K-32, 24LC32-4K- 32,24 LC64-8K-32, 24LC128-16K-64, 24LC256-32K-64, 24LC512-64K-128, read and write data are 8bits. The format for the above device (Model- address space- page size) of different devices of different sizes of pages, so page written procedures need to be amended accordingly, and other bytes to write, rand

标准IIC协议通信程序，能读写EEROM、实时时钟，使用方便，可靠！-Standard IIC protocol communication procedures, can read and write EEROM, real-time clock and easy to use, reliable!

在MSP430F247上实现的LCD12864的显示-MSP430F247 achieved in the display LCD12864

数码时钟显示，用8位LED软件译码动态显示，P0为字段码,P2为位选码，数码管共阳， key0为位选键；key1为加“1键；key2为减“1”键。-Digital clock display with 8 LED dynamic display software decoding, P0 code for the field, P2 election code for the digital, digital tube were positive, key0 bond election for the position key1 to add " 1 button key2 to reduce the" 1 " button.

NRF905芯片的C51发送子程序-NRF905 chip C51 sent subroutine

这是用台湾KingB 8位单片机开发的科学计算器程序，有一定的参考价值-This is used in Taiwan KingB 8-bit single chip scientific calculator developed procedures have certain reference value

本程序用于接收一般的红外线代码。很适合51单片机的新手学习。-This procedure is used to receive infrared codes in general. Very suitable for the novice to learn microcontroller 51.

这是一个步进电机调速的程序，可以完成100级的调速。-This is a stepper motor speed control procedures, to be completed 100 of the governor.