关于dSPACE的几篇文章，介绍了dSPACE的相关内容和应用，供大家参考。...

该代码采用c5400dsp的汇编语言和c语言实现双音多频信号的产生于检测，用在设计的电话通信系统中，经过实际测试，效果很好，接口为同步串口。-c5400dsp of assembly language and c language DTMF signals generated in the detection, used in the design of the telephone communication system, through the actual test and the results very good, synchronous serial interface.

TMS320C6713DSP模数转换程序源代码，AD芯片型号为ADS7864

3DSP 802.11b/g and Bluetooth 2.0 + EDR Wireless USB Mini Card Specification_V1_0-3DSP 802.11b/g and Bluetooth 2.0+ EDR Wireless USB Mini Card Specification_V1_0

基于TMS320F28335的DMA程序传送到SDRAM中，希望对大家学习有用，提供参考。来源于研旭DSP开发的DSP开发板。

修改TI例程后的DSP28335使用SCI中断读写数据，程序完整可以正常用运行，若使用RS485转USB需要加入485使能引脚转换。欢迎下载，如有问题随时可以联系。

F2812的USB检测程序，试过，好用。-F2812 the USB detection program, tried, easy to use.

dsp2812的合众达串行通信程序，可以用来参考，一切头文件都加载到里面了不只可以做SCI测试-Tatsu of the United dsp2812 serial communication procedures, can be used to reference all the header files are loaded into the inside of the SCI not only to make testing

这是在网上买的TMS320F28335开发板，店家免费提供的源程序，这是其中的一个小例程2833xCpuTimer.c，如果你想要更多的相关的TMS320F28335的源代码，我可以提供更多！

源程序是在VisualDSP环境下开发出来的，目标处理器是4片AD公司的TS1O1 DSP。IDE_FAT32用来在硬盘上创建FAT32文件系统；2）i2c_test编写IIC总线；3）codec_a_in_pal_cf_frame是加载到FLASH的程序，板子在脱离PC自动上电时会把PAL制的图像直接存到CF卡里，CF卡的文件系统是FAT16；4）codec_a_in_pal_buf_boottest是可加载的DSP图像直通程序；5）ADSP-TS101prog_driver是flash的驱动程序。-source of the VisualDSP environment developed, targeted four processor is the company"s AD TS1O1 DSP. IDE_FAT32 used in the drive to create FAT32 file system; 2) to prepare i2c_test IIC bus; 3) codec_a_in_pal_cf_frame FLASH is loading procedures, the board automatically from the PC on when power will be the PAL system images directly to CF card, the CF card is the FAT16 file system; 4) can be loaded codec_a_in_pal_buf_boottest DSP image through procedures; 5) ADSP-TS101prog_driver flash is the driver.

数字I/O实验主要完成的功能： 在此实验中，SEED-DEC5416 首选进行初始化，包括对外设 UART、本身频率的设定及一些状态区的初始化。然后等待 SEED-MMI5402 发送命令；SEED－DEC5416 响应交通灯自动模式、交通灯手动手动模式、交通灯东西通、交通灯南北通、及交通灯的禁行与夜间模式的操作命令。同时还响应，对 SEED-DEC5416 的复位及两个单元之间的通讯故障。 -Digital I/O completion of the experiment the main features: In this experiment, SEED-DEC5416 preferred to initialize, including peripherals UART, their frequency settings and some of the initialization state of the district. SEED-MMI5402 and then wait to send commands SEED-DEC5416 automatic mode in response to traffic lights, traffic lights manual manual mode, the traffic light east-west pass, pass traffic lights north and south, and traffic lights at night and cut-line mode command. At the same time, also responded to the SEED-DEC5416 reset and communication between two modules fault.