用DAC8532产生正弦波，包括c语言和汇编语言编程

胶印机印刷控制程序 -Offset printing control procedures

使用单片机C语言编的单片机实验板与上位机的串口通信（可接收上位机命令和根据命令给上位机上传上位机需要的数据）程序，可供单片机开发人员参考。-use C language series micro-controller board and PC serial communications (PC can receive orders and orders under the PC to PC to upload the data needed) process for the development of SCM reference.

基于凌阳SPCE061A单片机的多功能测频测相仪-Sunplus SPCE061A-based single-chip multi-frequency phase measuring instrument

51单片机ds1302驱动程序，肯定是好地-51 drivers, is certainly well

64点阵C程序有移动功能具有时间显示，可设置时间，断电保存-64 dot-matrix C procedures with mobile features the time display can be set-up times, power save

自制小时钟 可以遥控调节时间，采用315M 2262 ，2272 收发模块 发来给新手看看 -Self-made small-time clock can be adjusted remotely, using 315M 2262, 2272, sent to the transceiver module to see if novice

简易电子琴的设计 一、 设计题目： 设计一简易电子琴，要求能够发出1、2、3、4、5、6、7等七个音符。 使用元件：AT89C51、LM324，喇叭，按键等 二、 设计目的 （1）能够对电子电路、电子元器件、印制电路板等方面的知识有进一步的认识，独立对其进行测试与检查。 （2）熟悉8051单片机的内部结构和功能，合理使用其内部寄存器，能够完成相关软件编程设计工作。 （3）为实现预期功能，能够对系统进行快速的调试，并能够对出现的功能故障进行分析，及时修改相关软硬件。 （4）对软件编程、排错调试、焊接技术、相关仪器设备的使用技能等方面得到较全面的锻炼和提高。-simple design of a flower, a design : a simple flower design, request, sent seven notes. Use Element : AT89C51, LM324, speakers, such as two keys, designed (a) to be able to electronic circuits, electronic components, such as printed circuit boards with the knowledge to further understanding of its independent testing and inspection. (2) familiar with the 8051"s internal structure and function and the rational use of its internal registers can be completed software programming design work. (3) To achieve the desired functionality, the system can quickly debugging, and the right to function failure analysis, the timely revision of the related hardware and software. (4) The right software programming, debugg

51单片机产生锯齿波的程序-51 SCM procedures have Sawtooth

CAN总线与51单片机的接口原理图，使用的是sja1000和tja1040(philips).还包括了具体的文档资料和c语言控制代码(附加了LCD代码和LCD接口以及电源变换原理图).搞CAN总线一步到位.-CAN Bus and 51 microcontroller interface schematics, using the sja1000 and tja1040 (Philips). Also include the specific information and documentation control code language c (Additional code of LCD and LCD interfaces, and power transformation diagram). CAN engage in one go.

状态1：正常时，8个LED发光二极管（彩灯）循环点亮。 • 状态2：有报警时，蜂鸣器发出报警声（用P3.3接一个按键，模拟产生报警信号。当开关合上，发生报警；当开关断开，报警停止。用P3.7输出音频信号驱动扬声器，作为报警信号），同时8个LED发光二极管（彩灯）闪烁。 P3.2接一个按键，用于消除报警-Status 1: normal, eight LED light-emitting diodes (lantern) light cycle.