Linux版的嵌入式、、、可以实现数据的读入、

crossbow无线传感器网络节点例程,主要是做学习之用。-WSN tutorials

实用电子钟,为六位数码管时钟程序直接使用,p3.2,p3.3,p3.4,p3.5 四键控制！实测24小时误差5秒。-Practical electronic clock, nixie tube clock for the six programs used directly, p3.2, p3.3, p3.4, p3.5 four key control! Measured 24-hour error of 5 seconds.

三星ARM-ADS编译平台上的ARM S3C2440摄像头实例

你可曾经为硬件看门狗的复位时间太短,而苦恼过,这个方法帮你解决问题. 用定时器喂狗,如果超过一定时间(程序跑飞,或整个中断都关闭,都会导致定时器不喂狗,导致看门狗的复位,从而延长了看门狗的复位时间)不喂就复位. 程序中我以lcpRD2为例.-you may have to reset the hardware watchdog short time and anguish that this approach help you solve the problem. DOG with timers, if more than a certain time (running fly procedures, or were closed throughout the interruption, it will not lead to the timer DOG, resulting in the reduction watchdog, thereby prolonging the watchdog reset the time) do not feed on the reset. proceedings I lcpRD2 example.

资源描述NRF24L0x在STM32系统下的应用，可以使用地址作为多节点通信。

L298N是ST公司生产的一种高电压、大电流电机驱动芯片。该芯片采用15脚封装。主要特点是：工作电压高，最高工作电压可达46V；输出电流大，瞬间峰值电流可达3A，持续工作电流为2A；额定功率25W。内含两个H桥的高电压大电流全桥式驱动器，可以用来驱动直流电动机和步进电动机、继电器线圈等感性负载；采用标准逻辑电平信号控制；具有两个使能控制端，在不受输入信号影响的情况下允许或禁止器件工作有一个逻辑电源输入端，使内部逻辑电路部分在低电压下工作；可以外接检测电阻，将变化量反馈给控制电路。使用L298N芯片驱动电机，该芯片可以驱动一台两相步进电机或四相步进电机，也可以驱动两台直流电机。-L298N is produced by ST a high-voltage, high current motor driver chip. The chip uses 15-pin package. Main features are: high voltage, the maximum working voltage up to 46V output current, instantaneous peak current up to 3A, continuous operating current of 2A rated power of 25W. Contains two H-bridge high-voltage high-current full-bridge driver can be used to drive DC motors and stepper motors, relay coils and other inductive load using standard logic level signal control has two enable control terminal, input signal without affecting the case to permit or prohibit the device work a logic supply input, so that part of the internal logic circuits at low voltage work can be an external sense res

关于arm开发的文档集合 有uCLinux ,usb应用,以及开发步骤等等,非常不错,-development arm of the document set a uCLinux, usb applications, and the development of steps and so on. very good.

本文件是用keil编程的电子表的设计，实现时，分，秒的加减，和定时功能-This document is an electronic programming keil table design, the realization of hours, minutes and seconds of the addition and subtraction, and the timing

STM32F103的SSD1289驱动程序。

一个典型的推箱子游戏，内有代码，还有proteus仿真电路图。-A typical Sokoban game, there are codes, as well as proteus simulation circuit.