introduced the bus IC card circuit, the compilation of the original procedure

单片机控制水温的汇编程序，通过加热开关控制水温并显示温度！-SCM temperature control the compilation process, by heating water temperature control switches and display temperature!

SPI是一个环形总线结构，由ss（cs）、sck、sdi、sdo构成，其时序其实很简单，主要是在sck的控制下，两个双向移位寄存器进行数据交换。 假设下面的8位寄存器装的是待发送的数据10101010，上升沿发送、下降沿接收、高位先发送。 那么第一个上升沿来的时候 数据将会是sdo=1；寄存器=0101010x。下降沿到来的时候，sdi上的电平将所存到寄存器中去，那么这时寄存器=0101010sdi，这样在8个时钟脉冲以后，两个寄存器的内容互相交换一次。这样就完成里一个spi时序。 -SPI bus is a ring structure, by ss (cs), sck, sdi, sdo composition, its timing is actually very simple, mainly under the control of the sck and two bi-directional shift register for data exchange. Assuming the following 8-bit register is loaded to send the data to be 10,101,010, rising to send, receive falling edge, high first sent. Well, the first rising edge to the time data will be sdo = 1 register = 0101010x. Falling edge comes, sdi on the level will be stored to the register, then register at this time = 0101010sdi, so 8 clock pulse later, the contents of two registers to exchange time. This will be completed in a spi timing.

自制简易红外逻辑分析仪的单片机源程序，基本能完成我们的要求-Simple home-made infrared of single-chip logic analyzer source code, the basic requirements to complete our

单片机程序设计（uV2)-microcontroller programming (uV2)

此为继电器功能测试电路图DDB文件。对应源码为Relay_Function_Tester. keil c51 编写。-This is the relay circuit functional testing DDB file. The corresponding source code for Relay_Function_Tester. Keil c51 prepared.

无线传感器网络低占空比MAC协议研究 介绍MAC协议-mac protocol

LT_1B msp430开发板例子程序－TB12-LT_1B msp430开发板例子程序－TB2

320x240图形液晶驱动程序。经验证可以使用-320x240 graphic LCD driver. Certified can use the

240*160液晶驱动程序，厂家提供的源代码-240* 160 LCD driver, manufacturers provide source code

IC卡操作软件:AT88SCl604芯片的操作模式有五种。它们是通过配PGM、RST、CLK等引脚信号及内部地址计数器(IAC)的状态组合来实现。 (1) 芯片复位操作： AT88SCl604有两种复位方式:上电复位和控制复位。 上电复位： 上电复位是当芯片加电时的最初状态。上电复位属于芯片 内部复位。它将使芯片内部所有的隐含标志复位到"0"状态。并使地址计数器复位到0位。 控制复位： 当CLK为低时，在RST脚上的一个下降沿将便芯片产生复位操作。 控制复位是将地址计数器复位到0位，而不影响任何内部标志的状态。-IC Card operating software : AT88SCl604 chip mode of operation there are five. They are allocated by PGM, RST, etc. pin CLK signal and the internal address counter (IAC) portfolio of the state is to be achieved. (1) chip reset operation : reduction AT88SCl604 two ways : power-on reset and reset control. Power-on reset : power-on reset when the chip is in power at the initial state. Power-on reset the internal chip is reset. It will enable all internal chip implied signs reset to "0" state. Make address counter reset to 0. Reset control : When the CLK for the low, the RST feet of a falling edge chips will have to reset operation. Reset control is to address counter reset to 0, without prejudice to any signs of internal sta