利用pt2262作为发射端的主控芯片，该代码实现了控制pt2262的部分...

这是只能体温的毕业设计，其中包括了很全的毕业论证，这是一篇毕业论文。希望有用。-This is the only body temperature graduation project, which includes a very wide proof of graduation, this is a thesis. I hope useful.

基于51单片机，实现RS232和RS485两机通信，包含详细说明！

学习例程，共有100例，测试成功，在此上传工大家学习提高-Learning routines, a total of 100 cases, testing the success of workers in this upload them to learn to improve

编写一个延时1MS子程序根据题目选择是定时还是记数状态，本题选择记数状态。然后根据延时1MS计算出计时器的初值是E0H（高8位）18H（低5位）。最后编写算法，对T0初始化，利用T0的中断TF0调用中断处理程序。-prepared a delay rungs subroutine under the topic chosen is not a time to memorize numbers or state of mind of the few options that state. According to delay timer rungs calculate the initial value is E0H (high 8) 18H (Low 5). Preparation of the final algorithm, the T0 initialization, interrupt the use of T0 TF0 call interrupt handling procedures.

一个不错的PICC函数库说明，是PIC单片机开发工具资料-PICC a good library that is the PIC microcontroller development tool

此程序主要测试50HZ~3KHZ音频范围幅频特性测试程序.程序包含主控程序和显示程序.-This procedure tests the scope of 50HZ ~ 3KHZ audio amplitude-frequency characteristics of testing procedures. Procedures included control procedures and display program.

AVRMEG32编写的一个项目代码,里面包含一般应用的模块.-AVRMEG32 the preparation of a project code, which contains the general application of the module.

MCS-51单片机有5个中断源，其中两个是由-INT0、-INT1引脚输入的外部中断源；另外三个是内部中断源即由T0、T1的溢出引起中断和串行口发送完一个字节或接收到一个字节数据引起中断。触发外部中断有两种方式，即下降沿引起中断或低电平引起中断。当编程TCON中的ITi（i=0、1）为1时，则引起触发的方式为边沿触发方式，反之(ITi=0)为低电平触发方式。每个中断源的中断请求能否得到响应要受两级“开关”的控制，即一个总“开关”-MCS-51 single-chip has five interrupt sources, two of which are by-INT0,-INT1 pin input external interrupt source the other three internal interrupt sources from the T0, T1 overflow caused by the disruption and serial port sending or receiving end of a byte to a byte of data caused by interruption. Triggered external interrupt has two modes, namely, falling edge or low-level disruption caused disruption caused. When programming TCON in ITi (i = 0,1) for the 1:00 has been the subject of a way to trigger the way to the edge of the trigger, on the contrary (ITi = 0) for low-level trigger mode. Each interrupt source interrupt request can be subject to levels in response to

将数0000-9999用数码管依次循序显示 实验步骤: 1.打开伟福V3.20,创建一新文件 2.编写源代码 3.保存文件,文件名后缀为.asm 4.编译程序 5.打开Easy 51Pro v2.0将程序写进实验板-Experimental steps: 1. Open-wei Fu V3.20, create a new document 2. To prepare the source code 3. Save the file, the file name suffix to. Asm 4. Compiler 5. Easy 51Pro v2.0 to open the program into the board

利用NXP的新一代高集成度的芯片RC500完成Mifare系列卡的读写-The use of a new generation of highly integrated NXP" s Mifare chip RC500 Series completion card reader