12864串口液晶,包含两个文件:lcd.c与lcd.h. 调用 void printLCD(uint8 x,uint8 y,uint8 *fmt, ......

AVR开发板 C实现 液晶 can总线控制及其他外围电路源代码-AVR Development Board LCD can achieve C bus control, and other peripheral circuits source code

这是一个时钟中断的小程序-This is a small clock interrupt procedures

数字电子钟程序，计时时、分、秒，手动调整时间，闹铃，和整点报时-digital electronic clock procedures, a time when, minutes, and seconds, manual adjustments, Alarms, and the whole point is true.

STM32 通过串口flash更新程序, 不用固件库，包括: ADC采样, 定时器延时中断, 键盘扫描, 模拟I2C驱动 问题咨询: w123456xy@sohu.com 15189792379-STM32 through the serial flash update, without firmware libraries, including: ADC sampling, delay timer interrupt, keyboard scanning, I2C driver Advisory: w123456xy@sohu.com 15189792379

利用单片机的定时器定时，令十字路口的红绿灯交替点亮和熄灭，实现主支路路口的交通信号灯控制（尽可能保持主线的畅通，即在通常情况下，保持主线的放行，只有在支线到达时，才放行支线），同时采用LCD显示倒计时时间及当前灯的状态-The use of MCU timer timing, so that the crossroads at the traffic lights turn out light and to achieve the main slip road junction traffic lights control (as far as possible the smooth flow of the main line, that is, under normal circumstances, to maintain the release of the main line, and only arrived at the branch only when the release branch), while using LCD display countdown time and the current state of light

1.将P1.0～P1.3接开关，将P1.4～P1.7接发光二极管。依据P1.0～P1.3开关状态控制P1.4~P1.7发光二极管点亮。 2.将P1.0～P1.7全部接发光二极管，开始P1.0、P1.5点亮，左循环50次后P1.1、P1.4点亮；右循环30次，循环往复。-1. P1.0- P1.3 will then switch to P1.4- P1.7 access LEDs. P1.0- P1.3 based on state control switch P1.4- P1.7 LED lights. 2. P1.0- P1.7 will take all LEDs started Schematic, P1.5 lit, the left circle after 50 P1.1 and P1.4 lit; Turn right circle 30 times repeated.

crcmodula 进行 校验，在通信无线行业用的比较多-crcmodula to check, in communication with the wireless industry

vetess交换机管理软件，支持CLI管理，WEB管理，SNMP等各种常用管理功能-vetess switch management software, supports CLI management, Web management, SNMP management and other commonly used functions

基于ARM7开发系统的触摸屏校准程序，代码中有详细的中文注释，方便用户移植……-ARM7 development system based on the touch screen calibration procedures, a detailed code of the Chinese Notes user-friendly transplantation -ARM7 Development System Based on the touch screen calibration procedure, the code in detail the Chinese notes, user-friendly transplantation ... ...-ARM7 development system based on the touch screen calibration procedures, a detailed code of the Chinese Notes user-friendly transplantation

MSP430和LCD驱动芯片HT1621的驱动程序-MSP430 and LCD Driver IC HT1621 driver