C51学习实验程序－帮助初学单片机C语言的朋友学习使用

Medwin v2.39,51单片机开发利器-Medwin v2.39, 51 MCU Development weapon

Philip tea 5767 FM 驱动用应用程序 char FM_Init(char bandinfo, char softlev) -Philip tea 5767 FM applications driving char FM_Init (char bandinfo, char softlev)

单片机的动态显示程序设计-SCM dynamic display program design

由8051组成的单片机系统通常情况下，P0口分时复用作为地址、数据总线，P2口提供A15-A8即高8位地址，P3口用作第二功能，只有P1口通常用作I/0口。P1口是8位准双向口，它的每一位都可独立地定义为输入或输出，因此既可作为8位的并行I/O口，也可作为8位的输入输出端。当工作在输入方式时，对应位的锁存器必须先置1,才能正确地读到引脚上的信号,否则,执行读引脚指令时,若对应位的锁存器的值为0，读的结果永远为0。-By 8051, composed of single-chip microcomputer system under normal circumstances, P0 timeshare I reuse as address, data bus, P2 I provide A15-A8 high eight address, P3 mouth for the second function, I usually only P1 for I/0 I. P1 I was eight quasi-two-way port, it can be independent of each and every defined as input or output, it can be used as 8-bit parallel I/O port, can also be used as 8-bit input and output side. When the work in the input, the corresponding bit latch must first buy one in order to correctly read the signal pin, or pin the implementation of reading instruction, if the corresponding bit latch the value of 0, Reading the results of Forever to 0.

keil8.0的汉化，只是汉化菜单，其帮助文件没有汉化-keil8.0 a Chinese, a Chinese menu only, to help document does not finished

51单片机写的液晶显示程序（1602），调通的，供初学者参考-51 Single-chip LCD written procedures (1602), tune

三相步进电机的三相六拍工作方式，正转的绕组通电顺序：A、AB、B、BC、C、CA、A，反转的通电顺序：A、AC、C、CB、B、BA、B、A。 由于步进电机转子有一定的惯性以及所带负载的惯性，故步进电机的工作过程中不能及时的启动和停止，在启动时应慢慢的加速到预定速度，在停止前应逐渐减速到停止，否则，将产生失步现象。 步进电机的控制问题可总结为两点： 1、产生工作方式需要的时序脉冲； 2、控制步进电机的速度，使它始终遵循加速、匀速、减速的规律工作。 -Three-phase three-phase stepper motor six shot work, is to order the winding power: A, AB, B, BC, C, CA, A, reverse the order of power: A, AC, C, CB, B, BA, B, A. As the stepper motor rotor has a certain degree of inertia, as well as brought about by the inertia load, the stepper motor during the course of work should not start and stop time, start to be slowly accelerated to a predetermined speed, the stop should be to slow down gradually to the stop, otherwise, will result in out-of-step phenomenon. Stepper motor control problems can be summarized in two points: one, resulting in the need to work the timing pulse 2, control the speed of stepper motor, so that it always followed acceleration, velocity, deceleration of the law of the work.

PIC单片机程序设计基础 入门教程.-PIC Design Basics Guide.

用MEGA128做的串口服务器,包括原理图,源代码,TCPIP开发资料,接口包括RS232,RS485,RJ45-MEGA128 to do with the serial server, including schematics, source code, TCPIP development information, interface, including RS232, RS485, RJ45

rs485单线程数据通讯程序，KEY键触发能使单片机之间能够通讯-rs485 data communications single-threaded process, KEY key trigger enable communication between the single-chip