9012 infrared 9012_IR_jianma_program decoder c program to decode the received da...

基于单片机的数字灵敏电子钟设计，准确的实现时，分，秒显示-Based on the number of sensitive electronic clock microcontroller design, an accurate realization of hours, minutes, seconds displayed

用单片机实现在LED点阵上显示汉字，用C语言编写，用kile编译，再烧录在89S52上-MCU on the LED dot matrix display Chinese characters, using C language, compiler used kile, then burning on the 89S52

TI公司最新51系列内核单片机MSC1210Y2的数据资料。-TI

反汇编MSC-51系列单片机源码!目前支持BIN文件,要想支持HEX格式!大家可以自己下载去修改!目前版本没有识别DATA段功能!-Disassembly MSC-51 series single-chip source! Currently supports BIN file, in order to support HEX format! Everyone can download to change! Current version does not identify the DATA function para!

ModBus通信参考程序，Keil编译，学习ModBus的好工具-ModBusx protocol simulation, study well the instrument ModBus

单片机的程序，关于串口通讯的，对初学者来说说不定有用。-SCM procedures, on the serial communication, and may be useful for beginners.

8253的初始化程序举例: 例1：选择2号计数器，工作在3方式，计数初值为533H（2个字节），采用二进制计数。其初始化程序段为 MOV DX，307H ；命令口 MOV AL，10110110B ；2号计数器的初始化命 令字 OUT DX，AL ；写入命令寄存器 MOV DX，306H ；2号计数器数据口 MOV AX，533H ；计数初值 OUT DX，AL ；选送低字节到2号计数器 MOV AL，AH ；取高字节送AL OUT DX，AL ；后送高字节到2号计数器 -8253 initialization procedures examples : Example 1 : Select counters on the 2nd, in three ways. Counting for the initial 533H (2 bytes), a binary counting. Initialization of its procedures for MOV DX, 307H; I ordered MOV AL, 10110110B; on the 2nd Counter initialize command word OUT DX, AL; write commands Register MOV DX, 306H; data on the 2nd Counter I MOV AX, 533H; Counting initial OUT DX, AL; low-byte sent to the 2nd Counter MOV AL, AH; With a high-byte send AL OUT DX, AL; evacuations high byte counter to the 2nd

这是运用MSP430 单片机对字符行LCD 显示屏的驱动程序-This is the use of characters MSP430 line LCD display driver

用于CAN源代码.rar的头文件,一个不错的例程.-for source code. Rar the first document, a pretty good routine.

MCS-51单片机有5个中断源，其中两个是由-INT0、-INT1引脚输入的外部中断源；另外三个是内部中断源即由T0、T1的溢出引起中断和串行口发送完一个字节或接收到一个字节数据引起中断。触发外部中断有两种方式，即下降沿引起中断或低电平引起中断。当编程TCON中的ITi（i=0、1）为1时，则引起触发的方式为边沿触发方式，反之(ITi=0)为低电平触发方式。每个中断源的中断请求能否得到响应要受两级“开关”的控制，即一个总“开关”-MCS-51 single-chip has five interrupt sources, two of which are by-INT0,-INT1 pin input external interrupt source the other three internal interrupt sources from the T0, T1 overflow caused by the disruption and serial port sending or receiving end of a byte to a byte of data caused by interruption. Triggered external interrupt has two modes, namely, falling edge or low-level disruption caused disruption caused. When programming TCON in ITi (i = 0,1) for the 1:00 has been the subject of a way to trigger the way to the edge of the trigger, on the contrary (ITi = 0) for low-level trigger mode. Each interrupt source interrupt request can be subject to levels in response to