calculated in the design, such as : cash registers, calculators often encountere...

用MEGA128做的串口服务器,包括原理图,源代码,TCPIP开发资料,接口包括RS232,RS485,RJ45-MEGA128 to do with the serial server, including schematics, source code, TCPIP development information, interface, including RS232, RS485, RJ45

基于PIC16F877A的DS18B20一线总线多路测温系统（采用Proteus模拟）。 Proteus模拟电路图＋PIC C语言源程序（MPLAB V8.00） 这可不是用多I/O模拟的多路测温哦！看系统功能： 1）、由一线数据线寄生供电，采用MOSFET强上拉给DQ供电； 2）、上电自动搜索可用的传感器并做CRC校验（实现了Search ROM命令）； 3）、 报警下限可选择； 4）、轮询显示温度，通过LCD1602输出； 5）、 传感器中途拔出或温度越界均报警； 6）、 采用声光报警方式，可做为温度控制信号标志。 -PIC16F877A-based multi-channel bus of DS18B20 line temperature measurement system (using the Proteus simulation). Proteus analog circuit+ PIC C language source code (MPLAB V8.00) This is not using multiple I/O simulation of multi-channel temperature measurement Oh! See system functions: 1) by the parasitic power line data line, using MOSFET strong pull-up power supply to the DQ 2), power-on automatically search for available sensors and do CRC check (to achieve a Search ROM command) 3) alarm limit choice 4), polling shows the temperature, through the LCD1602 output 5), half-way pulled out or the temperature sensors are all cross-border police 6), using sound and light alarm mode can be used as the

《单片机C语言编程与实例》的代码集，可供参考编程用- Single-chip C language programming with examples of the code set is available for reference, programming by

自己写的 STM32 串口UART驱动, 不用固件库。超级终端界面按键时,自动回送。 应用范围: 因为不涉及IO口,所以此工程在STM32F1xx的任何主板上都可以运行。 编译器: IAR ARM 4.42A。 作者: w123456xy@sohu.com 15189792379。 -Write your own STM32 serial UART driver, no firmware library. HyperTerminal interface button, automatically send back. Application scope: because they do not involve IO port, so this works on any STM32F1xx motherboard can run. Compiler: IAR ARM 4.42A. Author: w123456xy@sohu.com 15189792379.

金鹏LCd的液晶串口显示程序，是金鹏网站上自带的历程，下载下来接可以用的直接。-Jinpeng LCd LCD serial display program is Jinpeng own course Web site, access can be downloaded directly.

单片机调试程序，液晶1602驱动程序，希望对大家有帮助-Single-chip debugger, LCD driver 1602, in the hope that we have to help

这个两个rar文件是关于定时器0使用的例子, 也是我第一次使用定时器0做的实验程序: 1. T0_ASM.rar, (带中文注释的C51语言例程), 利用定时器0中断实现LED灯的简单控制。 2. T0_C51.rar, (带中文注释的51汇编语言例程), 利用定时器0中断实现LED灯的简单控制。 两个同样功能的timer0中断程序都在MCU51-63K仿真器下通过实验, 小虾们可以试试看。 -Rar files that are both about the example of the use of Timer 0 is also the first to use my timer 0 of the experimental procedure to do: 1. T0_ASM.rar, (with English language routines C51 annotated), make use of the timer 0 interrupt implementation easy control of LED lights. 2. T0_C51.rar, (with English Notes 51 assembly language routines), use of the timer 0 interrupt achieve easy control of LED lights. Same function in both programs at timer0 interrupted MCU51-63K emulator through the experiment, shrimp can give it a try.

这是LCD1602与msp430之间的通信,其实可以直接从51移植过来,但是一定要在硬件加上拉电阻,要不然是不通不过的,我说的是你用的是5V的LCD-This is the LCD1602 and communication between the MSP430 can in fact be a direct transplant from the 51, but must be coupled with pull-up resistor in the hardware, otherwise it is unreasonable, however, I say is that you use the LCD is 5V

mp3设计原理图 设计思想 设计思路 设计步骤 明确清晰-mp3 schematic design design design design thinking clear steps

MCS51单片机的宏汇编器源程序-MCS51 the macro assembler source