凌阳061a单片机语音识别使用例程。包括两个基本语音识别例子可识别5条指令...

profibus从站模拟量接口模块设计.rar-Profibus station analog interface module design. Rar

简易数字温度计的设计与制作简易数字温度计的设计与制作-Simple digital thermometer design and production of simple digital thermometer design and production

MSP430单片机FLASH系列的PCB和原理图库，很好用的啊！-MSP430 Flash series and the PCB Principle Gallery, the good ah!

是数字温度传感器DS18B20和凌阳61单片机组成的温度预警系统的原理图和源程序。-Is a digital temperature sensor DS18B20 and Sunplus composed of 61 single-chip temperature warning system schematic and source code.

msp430 与12864的之间的通信,已经成功调试,不过因为12864的类型不一样,可能不能直接用,你还需要修改一下-12864 between the MSP430 and communications, has successfully debug, but because of the type not the same as 12864, may not be directly used, you also need to make some corrections

如何解决由于人不在家，所晾衣服被雨水淋湿的问题呢？作者利用义隆单片机EM78447A芯片设计出一种智能晾衣架，它能够自动识别晴天和雨天，智能地为我们服务-How to address people not at home because of the rain soaked clothes were hanging out the problem? The author uses Elan EM78447A single-chip intelligent chip design a drying rack, it can automatically identify the sunny and rainy days, smart for our Service

用proteus仿真的数字电压表 有8051单片机和adc0809以及4位数码管实现-Proteus simulation with digital voltage meter 8051 and has adc0809 as well as four digital tube realize

这是一个使用NOKIA 3510I的液晶屏+AVR单片机来制作的电压表，使用AVR单片机内部自带的ADC做电压采样。-This is a use of the NOKIA 3510I LCD+ AVR to produce single-chip voltage table, use the AVR s own single-chip internal voltage ADC sampling done.

this program tell you how to connect ps2 to a mcu(for example at89s51)-this program tell you how to connect to a ps2 mcu (for example at89s51)

1．熟悉硬件仿真工具KD30的使用。 2．修改样本程序 SAMP1a，使无论在计数或停止计数时，按 SW3 均对计数值清零，并停止计数。 3．编制一个秒表程序, 测试精度为0.1秒，按 SW1键启动计数，再按一次 SW1键停止计数。任何时候按 SW3 键停止计数，并对计数值清零。 4．按 SW1键后， 以 0.1 秒为单位开始计数，再按一次 SW1 键停止计数。若按 SW1 键时间超过2秒，则计数值清零，回到初始状态。-1. Familiar with the hardware simulation tool KD30 use. 2. Revised procedures SAMP1a samples, regardless of the count or counts at the end, according to SW3 numerical terms were right, reset, and stop counting. 3. Preparation of a stopwatch procedures, testing accuracy of 0.1 seconds, according to bond SW1 start counting, according to a key SW1 stopped counting. By SW3 any time to stop counting bond and reset the count. 4. By SW1 bond, after 0.1 seconds for start counting, according to a key SW1 stopped counting. If SW1 keys by the time more than two seconds, then reset the count and return to the initial state.