改进LSSVM迁移学习方法的轴承故障诊断(1)

说明：  位置跟踪器的matlab仿真代码，使用滑模控制方法(Location tracker matlab simulation code, using the sliding mode control method)

说明：  车间布局优化是将加工设备、物料输送设备、工作单元和通道走廊等布置物体合理地放置在一个有限的生产车间内的过程。车间布局优化模型是一个含有较为复杂约束的非线性连续优化模型，可以使用遗传算法进行优化。(Plant layout optimization is the process equipment, material handling equipment, work unit and access corridors and other layout objects placed in a reasonably limited production of the workshop process. Optimization Model is a workshop with more complex nonlinear continuous constrained optimization model, you can use the genetic algorithm optimization.)

人脸检测程序，只能针对单人，内附一些图片(Face detection process, only for a single person, enclosing some pictures)

数值方法计算传热问题实例 边长为200×200mm的二维矩形材料内的稳态温度分布。上侧和左侧维持恒壁温；下侧为绝热；右侧为对流换热条件。具体参数为： 材料的导热系数=20w/m• k； 上侧温度t1=100℃ 右侧流体温度tf=20℃ 表面传热系数 h分别为1w/m2• k和100 w/m2• k 左侧温度t2=20℃ 下侧绝热(Numerical method to calculate the heat transfer problem instance side of 200 × 200mm rectangular two-dimensional steady-state temperature distribution within the material. On the left side and to maintain constant wall temperature lower side of insulation the right side of the convective heat transfer conditions. Specific parameters are: thermal conductivity of the material = 20w/m • k on the side of the temperature t1 = 100 ℃ right side of the fluid temperature tf = 20 ℃ surface heat transfer coefficient h were 1w/m2 • k and 100 w/m2 • k temperature t2 = 20 ℃ left side of the insulation under)

本程序实现LPP降维功能，用于多模态故障诊断中(This procedure realize the LPP dimension reduction function, used in multimodal fault diagnosis )

独立变量分析，主成分分析，盲源分离经典算法，屡试不爽(ICA BSS)

本程序实现汉字和字符的识别匹配，通过该算法，可以实现手写体的字符和汉字的识别(This procedure to achieve identification of characters and character matching, through the algorithm, can achieve the character and Chinese character handwriting recognition)

用matlab编写的聚类rbf神经网络曲线拟和程序。(err)

说明：  这是仿真powell算法的简单程序，已经调试过了，效果不错，请大家多提宝贵意见(This is a simple simulation algorithm powell procedures, have been debug, good results, please mention the valuable advice)

提取信号七个基于瞬时信息的特征：零中心归一化瞬时幅度功率谱密度的最大值,零中心归一化瞬时幅度绝对值的标准偏差，零中心非弱信号段瞬时相位非线性分量绝对值标准偏差，零中心非弱信号段瞬时相位非线性分量标准偏差，零中心归一化的非弱信号段瞬时频率绝对值的标准偏差，一个信号段的归一化瞬时频率功率谱密度的最大值，根据信号 QPSK 和16QAM在 XI 轴投影的不同表现，提出特征参数。(extract information based on the instan eous features : In the center is one of the instantaneous rate of the power spectral density of the maximum, is a center to the absolute value of the instantaneous rate of the standard deviation, Non-zero weak signal instantaneous phase of the nonlinear component absolute standard deviation, Non-zero weak signal instantaneous phase of the nonlinear component standard deviation, In the center is one of the non-weak signal of the absolute value of the instantaneous frequency standard deviation, a signal to one of the instantaneous frequency of the power spectral density of the maximum, According to 16QAM and QPSK signals XI axis projection in the different performance parameters raised.)