串口6

labview实现神经bp网络,无需进入其他程序，在labview中就能运行(LabVIEW realizes neural network)

通过互相关求两信号的时延估计，包含labview源代码，可直接使用(Through each other for two signal delay estimation, including the LabVIEW source code, can be used directly)

本系统可做自动控制原理中的时域分析仿真实验，系统特性如下： 1：可选择仿真系统为一阶、二阶、任意阶 2：可选择信号源为正弦波、三角波、锯齿波、方波（可模拟阶跃信号），并可调节信号源频率、幅值、相位、偏移、方波占空比 3：可选择信号采样率及采样数 4：自动计算传递函数 5：自动计算时域响应参数（增益系数、上升时间、峰值、峰值时间、稳定时间、超调量） 6：波形图同时显示原始信号和响应信号 注：使用本系统需安装labview控制设计与仿真库(The system can do automatic control theory in the time-domain analysis simulation, the system behaves as follows: 1: simulation system can be selected for the first, second, any order 2: select the signal source is a sine wave, triangle wave, sawtooth, square wave (analog step signal), and can adjust the signal source frequency, amplitude, phase, offset, duty cycle square wave 3: the the optional signal sampling rate and the number of samples 4: automatic calculation of the transfer function 5: Automatic calculation domain response parameters (gain coefficient, rise time, peak, peak time, settling time, overshoot) 6: waveform diagram shows both the original signal and the response signal Note: Use the system to be installed LabVIEW Control Design and Simulation library)

串口自动换算CRC代码，编写时直接可以调用(Serial port automatically converts CRC code, which can be called directly when writing.)

说明：  PCI1020驱动，用于阿尔泰数据采集卡驱动(PCI1020 Driver for Altai Data Acquisition Card Driver)

说明：  基于LabvIEw的通用自动测试系统(ATs)舍计算机，可鳊程激励、响应数据采集及uuT模块，采用MxI总线控制方式。专用信号发生器为uuT提供模拟激励信号，矩阵开关和适配器完成不同信号间切换。主控计算机执行测试程序，信号发生器发送激励信号，数据采集卡采集数据，采集数据经调理后，并与标准数据|匕较是否满足相应测试结果。(The general automatic test system (ATs) based on LabvIEw can be used as a computer to excite, respond to data acquisition and uuT module. The control mode of MxI bus is adopted. Special signal generator provides analog excitation signal for uuT, matrix switch and adapter complete switching between different signals. The main control computer executes the test program, the signal generator sends the excitation signal, the data acquisition card collects the data, after the data acquisition is adjusted, and compares with the standard data | dagger whether it meets the corresponding test results.)

电机转速，基于labview。伺服电机控制程序(Motor speed based on LabVIEW. Servo motor control program)

labview 多通道数据采集监测系统 内附程序说明和描述(labview multi-channel data acquisition monitoring system included the description of the procedures and description)

在labview环境下编写的一个串口助手，可以读取数据，保存数据，截屏的功能，功能强大，适合初学者(A LabVIEW environment in the preparation of serial assistant, you can read the data, save data, screenshot function, powerful, suitable for beginners)

LABVIEW程序，实现BP神经网络，能达到目标精度。(This program is write for BP network)