MATLAB 参数都已知的GLRT检测

说明：  该程序给出了利用Saleh模型进行功率放大器预失真的过程．(The program gives the power amplifier pre-distortion with Saleh models.)

SLM算法降低OFDM通信系统中的PAPR，使用matlab进行仿真(SLM algorithm reduces PAPR in OFDM communication system, and matlab is used for simulation)

说明：  可实现绘制星型16QAM星座图，用于调制识别分类(Able to draw star 16QAM constellation diagram)

acquisition tension and frequency of sector

说明：  DS-CDMA的MMSE算法程序，给出了不同信噪比下的BER性能比仿真曲线。(DS-CDMA of the MMSE algorithm program are given under different signal to noise ratio curve of BER performance than emulation.)

基于模拟退火算法的光学模式转换，为模分复用一种高效转换算法。(Based on the optical mode conversion of simulated annealing algorithm, a high efficiency conversion algorithm is used for modular division multiplexing.)

本文分析了多级维纳滤波器的特性，在加性噪声和二维天线阵列如均匀圆阵、均匀面阵、十字阵等条件和背景下，对信源个数和信源参数估计问题进行了研究，提出了基于多级维纳滤波器前向分解特性的快速参数估计方法，同时提出了基于多级维纳滤波器的二维ESPRIT参数估计方法，该类方法无需协方差矩阵的估计运算及分解运算，计算复杂度较低。另外，还提出了对信源个数的估计算法。(This paper analyzes the characteristics of multistage Wiener filter, in the additive noise and the two-dimensional antenna array such as a uniform circular array, the uniform array, cross array conditions and background, the source number and source parameter estimation problem undertook study, put forward based on Multistage Wiener filter prior to the decomposition characteristics of fast parameter estimation method, at the same time based on Multistage Wiener filter 2D ESPRIT parameter estimation method, the method does not need to estimate of covariance matrix calculation and decomposition, relatively low computational complexity. In addition, also put forward for source number estimation algorithm.)

这是一个matlab和optisystem联合调试用的误码率计算程序，里面的文件报过一个可以用optisystem7和optisystem13可以打开的OSD仿真图，还有一个MATLAB计算BER的程序。给出了如何设置系统的大纲。从OptiSystem的电信号输入到Matlab组件。当OptiSystem运行时，它将调用Matlab组件中的M文件，处理数据，然后将所得的电信号导出回OptiSystem。然后将输出信号连接到BER分析仪。经过我调试，文件齐全，放心下载(The attached image gives an outline of how the system should be setup. You should start with inputting the electrical signal from OptiSystem into a Matlab component. When OptiSystem runs, it will call the M-file in the Matlab component, process the data, and then export the resulting electrical signal back into OptiSystem.The output signal is then connected to the BER Analyzer.)

研究d2d通信加中继节点来优化蜂窝小区边缘用户通信，并通过MATLAB仿真(The D2D communication and relay nodes are studied to optimize the edge user communication of cellular cell, and the simulation is carried out by MATLAB.)

ofdm源程序。正交频分复用(OFDM) 的源代码。(OFDM source program. The source code of the orthogonal frequency division multiplexing (OFDM).)