Get_HW_INFO

基于人工势场法的避障算法txt注释版本，非常详细(Obstacle avoidance algorithm based on artificial potential field method)

说明：  this is a test upload.... let me upload it for testing purpose please.. i really want to download a file

编号为1-52张牌，正面向上，从第2张开始，以2为基数，是2的倍数的牌翻一次，直到最后一张牌；然后，从第3张开始，以3为基数，是3的倍数的牌翻一次，直到最后一张牌；然后…从第4张开始，以4为基数，是4的倍数的牌翻一次， 直到最后一张牌；...再依次5的倍数的牌翻一次，6的，7的 直到 以52为基数的 翻过，输出：这时正面向上的牌有哪些？-No. 1-52 card in a positive, progressive, from the first two, with two as the base, 2 is a multiple of the license over time, until finally a license; Then, from the first three starting with three to the base, 3 is a multiple of the license over time, until finally a license; Then ... from the first four starting to four as the base, 4 is a multiple of the license over time, until finally a license; ... followed by the five multiples of the licensing repotted once, 6, 7 to 52 until the base of the turn, the output : At this time positive signs of upward What?

我给大家介绍一个好的动画制作软件――飘雪动画秀 V3.02，希望大家喜欢。-I give you a good animation software-- Falling Snow animation- V3.02, hope you like them.

这个是vb编写的控制服务器的程序，还包括一个于此相关的视频教程-This is the control server vb preparation procedures, this also includes a related video tutorial

说明：  Fluent.Ribbon 源码，类似office2010的界面，最近很流行的界面(Fluent. Ribbon source code, similar to the Office 2010 interface, the recently popular interface)

INS Matlab 仿真程序，用于惯性导航系统(INS Matlab simulation program, used for inertial navigation system)

1. 硬件接线 （1）调试串口(UART_Debug)使用UART2，在“printf.h”文件中宏定义， 对应引脚为TX-PTD7，RX-PTD6 （在“uart.h文件中宏定义）。 （2）灯0~3（LIGHT_0~LIGHT_3）对应的引脚是PTC0~PTC3，高电平点亮（由硬件接法决定） （3）SPI0_CLK对应的引脚是PTE0， SPI0_MOSI对应的引脚是PTE1， SPI0_MISO对应的引脚是PTE2，SPI0_PCS对应的引脚是PTE3， SPI1_CLK对应的引脚是PTG4， SPI1_MOSI对应的引脚是PTG5， SPI1_MISO对应的引脚是PTG6，SPI1_PCS对应的引脚是PTG7。 （4）SPI0作为master,SPI1作为slave，SPI1接收SPI0发送的数据并产生中断。 用导线将PTE0与PTG4对接，将PTE1与PTG5对接，将PTE2与PTG6对接，将PTE3与PTG7对接。(1. Hardware wiring (1) Debugging Serial Port (UART_Debug) uses UART2, macro-defined in "printf.h" file, corresponding pins are TX-PTD7, RX-PTD6. (macro definition in the uart.h file). (2) The pins corresponding to the lamp 0~3 (LIGHT_0~LIGHT_3) are PTC0~PTC3, and the high-level lighting is determined by the hardware connection. (3) The pin corresponding to SPI0_CLK is PTE0, and the pin corresponding to SPI0_MOSI is PTE1. The pin corresponding to SPI0_MISO is PTE2, and the pin corresponding to SPI0_PCS is PTE3. The pin corresponding to SPI1_CLK is PTG4, and the pin corresponding to SPI1_MOSI is PTG5. The pin corresponding to SPI1_MISO is PTG6, and the pin corresponding to SPI1_PCS is PTG7. (4) SPI0 acts as master and SPI1 acts as slave. SPI1 receives data sent by SPI0 and generates interruption. PTE0 and PTG4 are docked by wire, PTE1 and PTG5 are docked, PTE2 and PTG6 are docked, PTE3 and PTG7 are docked.)

说明：  画椭圆、矩形，勾勒出所需图形的大小与所在的位置。(Draw an ellipse or rectangle to outline the size and location of the desired graphic.)

这是个类似泡泡堂的游戏，用j2me编的，代码和图片完整，供大家下载(This is a game similar to paopaotang)